JVC RMP-2580U RM-P2580 Dome Controller Instructions (1148KB) - Page 18
JVC RMP-2580U - Remote Controller For Color Domes Manual
View all JVC RMP-2580U manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 18 highlights
3. APPLIED OPERATIONS ALARM OPERATION (Continued) Clearing the alarm The alarm operation can be cleared in two ways: When the time period specified in the ALARM TIME item in the ALARM screen has elapsed, the alarm operation stops automatically. ● The ALARM indicator turns off. ● The buzzer sound stops. ● The AUTO SEQUENCE mode returns to its situation before the alarm input. (A mode only) ● The camera which received the alarm signal returns to its setting before the alarm input. (AUTO PAN, AUTO PATROL or home position) ● The alarm title display clears. ● The UNIT ALARM maintains the MAKE position until the alarm conditions for all the cameras have been cleared. To set the alarm time REF. : [CONTROL UNIT SCREEN] on page 28 and [ALARM SCREEN : ALARM TIME] on page 32. NOTE When the ALARM TIME is set to SERIES, the alarm condition continues until the preset position, of the camera to which the alarm signal was input, is selected. When the alarm signal is received by the camera currently being selected, the alarm operation can be stopped by pressing the ENTER button. If the alarm signal is received by different camera, select that camera and press the ENTER button to stop the alarm operation. ● The ALARM indicator turns off. ● The buzzer sound stops. ● The alarm title display clears. ● The UNIT ALARM maintains the MAKE position until the alarm conditions for all the cameras have been cleared. DATA OUTPUT Three terminals, AUTO, UNIT ALARM and SELECT OUT / ALARM are provided at the Data Output terminal. ● AUTO terminal Signals are output when the AUTO SEQUENCE starts. ● UNIT ALARM terminal Signals are continuously output during an ALARM occurrence. ● SELECT OUT / ALARM terminal When a particular camera or camera position is selected by using a combination of the numeric keypad and the CAMERA, POSITION buttons, the corresponding command signal is output via one of the DATA I/O terminals on the rear panel. REF. : See "DATA I/O SCREEN" on page 30, 31 for the assignment of each terminal. DATA I/O terminals For details of signal types to be output from each terminal; REF. : Page 20 for the A Mode, and page 22 for the B Mode. RX+ RX- TX+ TX- TO CAMERA COM 1 2 3 4 5 6 7 8 DATA I / O UNIT CAMERA COM 9/1 10/2 11/3 12/4 13/5 14/6 15/7 16/8 COM AUTO ALARM COM SW COM SERIAL-1 SERIAL-2 POWER ON OFF 1 2 3 4 VIDEO INPUT 5 6 7 8 MONITOR MONITOR OUTPUT OUTPUT 1 2 AC`INPUT 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 VIDEO OUTPUT 6 7 8 CAMERA SWITCHING OPERATION By means of a CAM SW signal from a Time Lapse VCR which is connected to the CAMERA SW terminals, the video signal from MONITOR OUTPUT 2 can be selected to feed the Time Lapse VCR. ● When switching the video signal with the CAM SW, be sure to set the CAMERA SELECTION item to ENABLE. Otherwise the video signal will not be switched correctly. REF. : "OPTION SCREEN: CAMERA SELECTION" on page 29. ● Setting alterations are necessary according to which time-lapse VCR is connected. REF. : "CONTROL UNIT SCREEN" on page 28 and "DATA I/O screen: CAM SWITCH Item" on page 30 Set the CAM SWITCH to LOW when a time-lapse VCR of JVC is connected. NOTE To switch the Alarm signal correctly by the CAM SW signal, set it in the following manner: ● Make sure that video signals are input to VIDEO INPUT 1. ● Make sure that the recording hours for the time-lapse VCR are set for 24 hours or more. ● Make sure the CAMERA SELECTION item is set to ENABLE for VIDEO INPUT 1. 18