Kenmore 4031 Use and Care Guide - Page 8

Unpacking, Removing, Shipping, Bolts

Get Kenmore 4031 - 4.2 cu. Ft. Front-Load Washer PDF manuals and user guides View all Kenmore 4031 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

UNPACKING AND REMOVING SHIPPING BOLTS When removing the washer from the carton base, be sure to remove the foam tub support in the middle of the carton base. See drawing below. If you must lay the washer down to remove the base packaging materials, always protect the side of the washer and lay it carefully on its side. DO NOT lay the washer on its front or back. To prevent internal damage during transport, the washer is equipped with 4 shipping bolts and plastic retainers. IMPORTANT: •These shipping bolts and retainers MUST NOT be removed until just before moving the washer into its final position. •These bolts and retainers MUST be removed before operating the washer. • Failure to remove shipping bolts and retainers may cause severe vibration and noise, which can lead to permanent damage to the washer. NOTE: The cord is secured to the back of the washer with a shipping bolt to help prevent operation with shipping bolts in place. Shipping Bolts Power Cord J 1. Starting with the bottom 2 shipping bolts, use the included wrench to fully loosen the 4 shipping bolts by turning them counterclockwise. Foam Tub Support Carton Base \ Bolt Assembly HoleCap , 2. Remove the bolt assemblies by wiggling them slightly while pulling. 3. Locate the four hole caps included in the accessory pack and install them in the shipping bolt holes. NOTE: Save the bolt assemblies for future use. To prevent damage to internal components, the bolt assemblies must be installed when transporting the washer.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
UNPACKING
AND
REMOVING
SHIPPING
BOLTS
When removing the washer from the carton base, be sure to
remove the foam tub support in the middle of the carton
base. See drawing below.
If you must lay the washer down to remove the base
packaging materials, always protect the side of the washer
and lay it carefully on its side. DO NOT lay the washer on its
front or back.
To prevent internal damage during transport, the washer is
equipped with 4 shipping bolts and plastic retainers.
IMPORTANT:
•
These shipping bolts and retainers
MUST NOT
be
removed until just before moving the washer into its final
position.
•These bolts and retainers MUST be removed before
operating the washer.
• Failure to remove shipping bolts and retainers may cause
severe vibration and noise, which can lead to permanent
damage to the washer.
NOTE: The cord is secured to the back of the washer with a
shipping bolt to help prevent operation with shipping bolts in
place.
Foam Tub
Support
Carton
Base
Shipping
Bolts
Power
Cord
J
1. Starting with the bottom 2 shipping bolts, use the included
wrench to fully loosen the 4 shipping bolts by turning them
counterclockwise.
\
Bolt
Assembly
HoleCap
,
2. Remove the bolt assemblies by wiggling them slightly
while pulling.
3. Locate the four hole caps included in the accessory pack
and install them in the shipping bolt holes.
NOTE: Save the bolt assemblies for future use. To prevent
damage to internal components, the bolt assemblies must
be installed when transporting the washer.