Kodak 8536096 User Guide - Page 8

Finding a location for your printer dock, Installing the custom camera insert

Get Kodak 8536096 - Easyshare Printer Dock PDF manuals and user guides
UPC - 041778536094
View all Kodak 8536096 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Getting started Finding a location for your printer dock ■ Place the printer dock on a flat, clean, dust-free surface, in a dry location, and out of direct sunlight. ■ Allow 5 in. (12.7 cm) clearance on all sides of the printer dock. ■ For proper ventilation, make sure the top and back of the printer dock are not blocked. ■ When connecting power or USB cables, keep the cables clear of the paper path to the front and rear of the printer dock. ■ Avoid areas where ventilation ducts, open doors, or frequent passersby might expose the printer dock and paper to high levels of dust and debris. Airborne dirt particles can affect picture quality. Installing the custom camera insert The printer dock comes with a universal camera insert already installed. The insert allows most Kodak EasyShare CX/DX6000/7000 series and LS600/700 series digital cameras to fit on the printer dock. For best fit, use the custom camera insert that came with your camera and keep the universal camera insert as a spare. NOTE: For some cameras, you must use the custom camera insert to dock the camera, otherwise the camera will not fit properly on the printer dock. 1 Remove the universal camera insert: a Push the insert toward the back of the printer dock and lift up the front edge. b Lift up the back edge of the insert and remove. 2 Install the custom camera insert included with your camera: a Place the rear tabs of the insert in the slots toward the back of the printer dock. b Press the front of the insert down and snap into place. 2 www.kodak.com/go/support

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
Getting started
2
www.kodak.com/go/support
Finding a location for your printer dock
■
Place the printer dock on a flat, clean, dust-free surface, in a dry location,
and out of direct sunlight.
■
Allow 5 in. (12.7 cm) clearance on all sides of
the printer dock.
■
For proper ventilation, make sure the top and
back of the printer dock are not blocked.
■
When connecting power or USB cables, keep
the cables clear of the paper path to the front
and rear of the printer dock.
■
Avoid areas where ventilation ducts, open doors, or frequent passersby
might expose the printer dock and paper to high levels of dust and debris.
Airborne dirt particles can affect picture quality.
Installing the custom camera insert
The printer dock comes with a universal camera insert already installed. The
insert allows most Kodak EasyShare CX/DX6000/7000 series and LS600/700
series digital cameras to fit on the printer dock.
For best fit, use the custom camera insert that came with your camera and
keep the universal camera insert as a spare.
NOTE: For some cameras, you
must
use the custom camera insert to dock the camera, otherwise
the camera will not fit properly on the printer dock.
1
Remove the universal camera insert:
a
Push the insert toward the back of the
printer dock and lift up the front edge.
b
Lift up the back edge of the insert and
remove.
2
Install the custom camera insert included with
your camera:
a
Place the rear tabs of the insert in the slots
toward the back of the printer dock.
b
Press the front of the insert down and snap
into place.