Kyocera TASKalfa 6501i PCL Barcode Flash 3.0 User's Manual Rev 3.2.03.2013 - Page 25

Activating and deactivating the software Type A only

Get Kyocera TASKalfa 6501i PDF manuals and user guides View all Kyocera TASKalfa 6501i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

2.2 Activating and deactivating the software (Type A only) Before you can use the software on the CF card in your printer, you have to make this available to the device by activating it. To do this, you have two options:  Call the partition Barcode Init via the front panel on your printer, or  Send the PRESCRIBE sequence !R! FRPO I0, "KM BC 3.02.1"; EXIT; to the printer. If you are using a later version, the name of the newer partition must be used instead of "KM BC 3.02.1". To see the exact name of the program partition, print a partition list. Automatic loading of the software on the CF card is now activated, and once the device has been switched on the barcode solution will be immediately available. Note You have to set your printer to 600 dpi minimum to be able to use the software You can optionally configure your printer via the front panel or the PRESCRIBE sequence !R! FRPO N8,1; EXIT; . Depending on how you are using it, it may sometimes be sensible (e.g. for testing purposes) to deactivate the software occasionally. You have two options for doing this:  Remove the CF card from the device or  Deactivate the CF card by calling the Barcode Remove partition The software will no longer be available the next time you start the printer. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
25
2.2 Activating and deactivating the software (Type A only)
Before you can use the software on the CF card in your printer, you have to make
this available to the device by activating it.
To do this, you have two options:
Call the partition
Barcode Init
via the front panel on your printer,
or
Send the PRESCRIBE sequence
!R!
FRPO I0, “KM BC 3.0
2
.1”; EXIT;
to the printer. If you are using a later version, the name of the newer partition
must be used instead of “KM BC
3.02
.1”. To see the exact name of the program
partition, print a partition list.
Automatic loading of the software on the CF card is now activated, and once the
device has been switched on the barcode solution will be immediately available.
Note
You have to set your printer to 600 dpi minimum to be able to use the
software You can optionally configure your printer via the front panel or the
PRESCRIBE sequence
!R! FRPO N8,1; EXIT;
.
Depending on how you are using it, it may sometimes be sensible (e.g. for testing
purposes) to deactivate the software occasionally. You have two options for doing
this:
Remove the CF card from the device
or
Deactivate the CF card by calling the
Barcode Remove
partition
The software will no longer be available the next time you start the printer.