Kyocera TASKalfa 6501i PCL Barcode Flash 3.0 User's Manual Rev 3.2.03.2013 - Page 50

Lowest symbol version, Highest symbol version, Type of encoding, Error correction level, Quantity

Get Kyocera TASKalfa 6501i PDF manuals and user guides View all Kyocera TASKalfa 6501i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

The module size unit was previously specified using the UNIT command. We recommend that you use dots (pixels). Lowest symbol version Values from 1 to 40. For an explanation of the meaning of this parameter, cf. the explanatory notes on the h parameter in the section "SYNTAX IN PCL". Highest symbol version Values from 1 to 40. For an explanation of the meaning of this parameter, cf. the explanatory notes on the h parameter in the section "SYNTAX IN PCL". Type of encoding Values from 0 to 4. For an explanation of the meaning of this parameter, cf. the explanatory notes on the s parameter in the section "SYNTAX IN PCL". Error correction level Values from 1 to 4. For an explanation of the meaning of this parameter, cf. the explanatory notes on the b parameter in the section "SYNTAX IN PCL". Quantity of base data in bytes The base data can be passed in three different ways. The quantity of base data only needs to be specified if the data is being passed in the first of the ways set out below: 1. By appending it after the semi-colon, which closes the BARC command, in this case the number of bytes must be indicated. 2. In inverted commas. 3. By appending it after the semi-colon, which closes the BARC command. The bytes are closed by the WRED command. Example 1 !R!UNIT D;BARC 102,10,13,14,2,4,11;EXIT; here corresponds to exactly 11 bytes. Example 2 !R!UNIT D;BARC 102,10,13,14,2,4,"";EXIT; In this instance it is not necessary to specify the number of bytes. 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
50
The module size unit was previously specified using the
UNIT
command. We
recommend that you use dots (pixels).
Lowest symbol version
Values from 1 to 40. For an explanation of the meaning of this parameter, cf. the
explanatory notes on the h pa
rameter in the section “
S
YNTAX IN
PCL
”.
Highest symbol version
Values from 1 to 40. For an explanation of the meaning of this parameter, cf. the
explanatory notes on the h parameter in the section “
S
YNTAX IN
PCL
”.
Type of encoding
Values from 0 to 4. For an explanation of the meaning of this parameter, cf. the
explanatory notes on the s parameter in the section “
S
YNTAX IN
PCL
”.
Error correction level
Values from 1 to 4. For an explanation of the meaning of this parameter, cf. the
explanatory notes on the
b parameter in the section “
S
YNTAX IN
PCL
”.
Quantity of base data in bytes
The base data can be passed in three different ways.
The quantity of base data only needs to be specified if the data is being passed in the
first of the ways set out below:
1. By appending it after the semi-colon, which closes the
BARC
command,
in this case the number of bytes must be indicated.
2. In inverted commas.
3. By appending it after the semi-colon, which closes the
BARC
command.
The bytes are closed by the
WRED
command.
Example 1
!R!UNIT D;BARC 102,10,13,14,2,4,11;<Base Data>EXIT;
<Base Data> here corresponds to exactly 11 bytes.
Example 2
!R!UNIT D;BARC 102,10,13,14,2,4,“<Base Data>“;EXIT;
In this instance it is not necessary to specify the number of bytes.