LG LREL6321S Owners Manual - Page 46

EasyClean, Start, Clear/Off, Clear

Get LG LREL6321S PDF manuals and user guides View all LG LREL6321S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

46 MAINTENANCE 5 Spray or pour the remaining water (8 oz or 250 ml) onto the bottom center of the oven cavity. The indentation on the oven bottom should be fully covered to submerge all soils. Add water if necessary. NOTE If cleaning multiple ovens, use an entire bottle of water to clean each oven. Do not spray water directly on the door. Doing so will result in water (10 oz or 300 ml) dripping to the floor. 6 Close the oven door. Press EasyClean®. Press Start. CAUTION •• Some surfaces may be hot after the EasyClean® cycle. Wear rubber gloves while cleaning to prevent burns. •• During the EasyClean® cycle, the oven becomes hot enough to cause burns. Wait until the cycle is over before wiping the inside surface of the oven. Failure to do so may result in burns. •• Avoid leaning or resting on the oven door glass while cleaning the oven cavity. 7 A tone will sound at the end of the 10 minute cycle. Press Clear/Off to clear the display and end the tone. 8 After the cleaning cycle and during handcleaning, enough water should remain on the oven bottom to completely submerge all soils. Add water if necessary. Place a towel on the floor in front of the oven to capture any water that may spill out during hand-cleaning. 9 Clean the oven cavity immediately after the EasyClean® cycle by scrubbing with a wet, non-scratch scouring sponge or pad. (The scouring side will not scratch the finish.) NOTE Do not use any steel scouring pads, abrasive pads or cleaners as these materials can permanently damage the oven surface. 10 Once the oven cavity is cleaned, wipe any excess water with a clean dry towel. Replace racks and any other accessories. 11 If some light soils remain, repeat the above steps, making sure to thoroughly soak the soiled areas. If stubborn soils remain after multiple EasyClean® cycles, run the Self Clean cycle. Be sure that the oven cavity is empty of oven racks and other accessories, and that the oven cavity surface is dry before running the Self Clean cycle. Consult the Self Clean section of your owner's manual for further details. If a self-clean option is not available, scrape off and remove stubborn soil using a scraper. NOTE •• If you forget to saturate the inside of the oven with water before starting EasyClean®, press Clear/ Off to end the cycle. Wait for the range to cool to room temperature and then spray or pour water (10 oz or 300 ml) into the oven and start another EasyClean® cycle. •• The cavity gasket may be wet when the EasyClean® cycle finishes. This is normal. Do not clean the gasket. •• If mineral deposits remain on the oven bottom after cleaning, use a cloth or sponge soaked in vinegar to remove them. •• It is normal for the fan to operate during the EasyClean® cycle.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
46
MAINTENANCE
5
Spray or pour the remaining water (8 oz or 250
ml) onto the bottom center of the oven cavity.
The indentation on the oven bottom should be
fully covered to submerge all soils. Add water if
necessary.
NOTE
If cleaning multiple ovens, use an entire bottle
of water to clean each oven. Do not spray water
directly on the door. Doing so will result in water
(10 oz or
300 ml) dripping to the floor.
6
Close the oven door.
Press
EasyClean
®
.
Press
Start
.
CAUTION
•
Some surfaces may be hot after the
EasyClean® cycle. Wear rubber gloves while
cleaning to prevent burns.
•
During the EasyClean® cycle, the oven
becomes hot enough to cause burns. Wait
until the cycle is over before wiping the inside
surface of the oven. Failure to do so may result
in burns.
•
Avoid leaning or resting on the oven door glass
while cleaning the oven cavity.
7
A tone will sound at the end of the 10 minute
cycle. Press
Clear/Off
to clear the display and
end the tone.
8
After the cleaning cycle and during hand-
cleaning, enough water should remain on the
oven bottom to completely submerge all soils.
Add water if necessary. Place a towel on the
floor in front of the oven to capture any water
that may spill out during hand-cleaning.
9
Clean the oven cavity immediately after the
EasyClean
®
cycle by scrubbing with a wet,
non-scratch scouring sponge or
pad. (The scouring side will not
scratch the finish.)
NOTE
Do not use any steel scouring pads, abrasive
pads or cleaners as these materials can
permanently damage the oven surface.
10
Once the oven cavity is cleaned, wipe any
excess water with a clean dry towel. Replace
racks and any other accessories.
11
If some light soils remain, repeat the above
steps, making sure to thoroughly soak the
soiled areas.
If stubborn soils remain after multiple
EasyClean
®
cycles, run the Self Clean cycle.
Be sure that the oven cavity is empty of oven
racks and other accessories, and that the oven
cavity surface is dry before running the Self
Clean cycle. Consult the Self Clean section of
your owner’s manual for further details.
If a self-clean option is not available, scrape
off and remove stubborn soil using a scraper.
NOTE
•
If you forget to saturate the inside of the oven with
water before starting EasyClean
®
, press
Clear/
Off
to end the cycle. Wait for the range to cool to
room temperature and then spray or pour water
(10 oz or 300 ml)
into the oven and start another
EasyClean
®
cycle.
•
The cavity gasket may be wet when the
EasyClean
®
cycle finishes. This is normal. Do not
clean the gasket.
•
If mineral deposits remain on the oven bottom after
cleaning, use a cloth or sponge soaked in vinegar
to remove them.
•
It is normal for the fan to operate during the
EasyClean
®
cycle.