Lenovo ThinkCentre A58e Hardware Maintenance Manual - Page 62

Voltage Sensors Test Passed, Microprocessor Test Passed

Get Lenovo ThinkCentre A58e PDF manuals and user guides View all Lenovo ThinkCentre A58e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Diagnostic Error Code 086-197-XXX Mouse Port interface test warning 086-198-XXX Mouse Port interface test aborted 086-199-XXX Mouse Port interface test failed, cause unknown 089-000-XXX Microprocessor Test Passed 089-XXX-XXX Microprocessor failure 089-195-XXX Microprocessor Test aborted by user 089-196-XXX Microprocessor test halt, error threshold exceeded 089-197-XXX Microprocessor test warning 089-198-XXX Microprocessor test aborted 089-199-XXX Microprocessor test failed, cause unknown 170-000-XXX Voltage Sensor(s) Test Passed 170-0XX-XXX Voltage Sensor(s) failure 170-195-XXX Voltage Sensor(s) Test aborted by user FRU/Action 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 "Diagnostics, Test and Recovery Information" on page 37 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6 "Diagnostics, Test and Recovery Information" on page 37 2. Flash the system and re-test. See "Flash update procedures" on page 91 3. Go to "Undetermined problems" on page 63 1. See "Undetermined problems" on page 63 2. Flash the system and re-test. See "Flash update procedures" on page 91 3. Replace component under function test No action 1. Microprocessor(s) 2. System board Information only Re-start the test, if necessary 1. Press F3 to review the log file 2. Re-start the test to reset the log file 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 "Diagnostics, Test and Recovery Information" on page 37 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 1. Flash the system. See "Flash update procedures" on page 91 2. Go to "Undetermined problems" on page 63 1. See "Undetermined problems" on page 63 2. Flash the system and re-test. See "Flash update procedures" on page 91 3. Replace component under function test No action 1. Flash system 2. System board Information only Re-start the test, if necessary 56 ThinkCentre Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Diagnostic Error Code
FRU/Action
086-197-XXX
Mouse Port interface test warning
1.
Make sure the component that is called out
is connected and/or enabled. See Chapter 6
“Diagnostics, Test and Recovery Information” on
page 37
2.
Re-run test
3.
Replace the component that is called out in warning
statement
4.
Replace the component under test
086-198-XXX
Mouse Port interface test aborted
1.
If a component is called out, make sure it is
connected and/or enabled. See Chapter 6
“Diagnostics, Test and Recovery Information” on
page 37
2.
Flash the system and re-test. See “Flash update
procedures” on page 91
3.
Go to “Undetermined problems” on page 63
086-199-XXX
Mouse Port interface test failed, cause
unknown
1.
See “Undetermined problems” on page 63
2.
Flash the system and re-test. See “Flash update
procedures” on page 91
3.
Replace component under function test
089-000-XXX
Microprocessor Test Passed
No action
089-XXX-XXX
Microprocessor failure
1.
Microprocessor(s)
2.
System board
089-195-XXX
Microprocessor Test aborted by user
Information only
Re-start the test, if necessary
089-196-XXX
Microprocessor test halt, error threshold
exceeded
1.
Press F3 to review the log file
2.
Re-start the test to reset the log file
089-197-XXX
Microprocessor test warning
1.
Make sure the component that is called out
is connected and/or enabled. See Chapter 6
“Diagnostics, Test and Recovery Information” on
page 37
2.
Re-run test
3.
Replace the component that is called out in warning
statement
4.
Replace the component under test
089-198-XXX
Microprocessor test aborted
1.
Flash the system. See “Flash update procedures”
on page 91
2.
Go to “Undetermined problems” on page 63
089-199-XXX
Microprocessor test failed, cause unknown
1.
See “Undetermined problems” on page 63
2.
Flash the system and re-test. See “Flash update
procedures” on page 91
3.
Replace component under function test
170-000-XXX
Voltage Sensor(s) Test Passed
No action
170-0XX-XXX
Voltage Sensor(s) failure
1.
Flash system
2.
System board
170-195-XXX
Voltage Sensor(s) Test aborted by user
Information only
Re-start the test, if necessary
56
ThinkCentre Hardware Maintenance Manual