Lexmark C748 Quick Reference - Page 15

Loading narrow paper sizes such as envelopes and A6

Get Lexmark C748 PDF manuals and user guides View all Lexmark C748 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

5 Load the paper stack toward the back of the tray with the recommended printable side faceup. Notes: • When loading preprinted letterhead for one‑sided printing, place the letterhead faceup toward the front of the tray. • When loading preprinted letterhead for two‑sided printing, place the letterhead facedown toward the rear of the tray. One‑sided printing Two‑sided (Duplex) printing LETTERHEAD LETTERHEAD Note: Make sure the paper does not exceed the maximum paper fill indicator located on the left side of the tray. Warning-Potential Damage: Overloading the tray can cause paper jams and possible printer damage. 6 Insert the tray. Note: For some paper sizes, the tray will extend past the back of the printer. 7 From the printer control panel, verify the paper size and paper type setting for the tray based on the paper you loaded. Loading the optional 550‑sheet special media tray The optional 550‑sheet special media tray (Tray 2) supports narrow paper sizes such as envelopes and A6. 2 1 3 4 15 1 Primary length guide 2 Length guide lock 3 Secondary length guide 4 Width guide CAUTION-POTENTIAL INJURY: To reduce the risk of equipment instability, load each paper drawer or tray separately. Keep all other trays closed until needed. Notes: • For instructions on loading paper sizes larger than A6 and envelopes, see "Loading the standard or an optional 550‑sheet tray" on page 14. • For a complete list of supported paper sizes, see the "Supported paper sizes, types, and weights" section in the User's Guide. Loading narrow paper sizes such as envelopes and A6 1 Pull the tray completely out. Note: Do not remove trays while a job prints or while Busy appears on the display. Doing so may cause a jam. 2 Squeeze and slide the primary length guide toward you until it stops. Notes: • The length has a locking device. To unlock the length guide, slide to the left the button on top of the length guide. To lock, slide the button to the right when a length has been selected. • You can only slide the secondary length guide when the primary length guide reaches the edge of the width guide.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
5
Load the paper stack toward the back of the tray with the
recommended printable side faceup.
Notes:
•
When loading preprinted letterhead for one
‑
sided printing,
place the letterhead faceup toward the front of the tray.
•
When loading preprinted letterhead for two
‑
sided printing,
place the letterhead facedown toward the rear of the tray.
One
‑
sided printing
Two
‑
sided (Duplex) printing
LETTERHEAD
LETTERHEAD
Note:
Make sure the paper does not exceed the maximum paper
fill indicator located on the left side of the tray.
Warning—Potential Damage:
Overloading the tray can cause
paper jams and possible printer damage.
6
Insert the tray.
Note:
For some paper sizes, the tray will extend past the back of
the printer.
7
From the printer control panel, verify the paper size and paper type
setting for the tray based on the paper you loaded.
Loading the optional 550
‑
sheet special media
tray
The optional 550
‑
sheet special media tray (Tray 2) supports narrow
paper sizes such as envelopes and A6.
1
2
3
4
1
Primary length guide
2
Length guide lock
3
Secondary length guide
4
Width guide
CAUTION—POTENTIAL INJURY:
To reduce the risk of
equipment instability, load each paper drawer or tray
separately. Keep all other trays closed until needed.
Notes:
•
For instructions on loading paper sizes larger than A6 and
envelopes, see “Loading the standard or an optional 550
‑
sheet
tray” on page 14.
•
For a complete list of supported paper sizes, see the "Supported
paper sizes, types, and weights" section in the
User's Guide
.
Loading narrow paper sizes such as envelopes and A6
1
Pull the tray completely out.
Note:
Do not remove trays while a job prints or while
Busy
appears on the display. Doing so may cause a jam.
2
Squeeze and slide the primary length guide toward you until it
stops.
Notes:
•
The length has a locking device. To unlock the length guide,
slide to the left the button on top of the length guide. To
lock, slide the button to the right when a length has been
selected.
•
You can only slide the secondary length guide when the
primary length guide reaches the edge of the width guide.
15