Maytag MGDB700VQ Use and Care Guide - Page 23

thebulbwitha10-watt

Get Maytag MGDB700VQ - MaytagR BravosR Gas Dryer PDF manuals and user guides
UPC - 883049140582
View all Maytag MGDB700VQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

2. Openthedryedr oorI._ocattheelightbulbcoveor nthebackwallofthedryerR. emove 3. TurnbulbcounterclockwRiseep.lactheebulbwitha 10-waattppliancbeulbonly. thescrewlocateidnthelowerighct orneorfthecoverR. emovtheecover. Replactheecovearndsecurweiththescrew. 4. Plugindryeor rreconnepcot wer. First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of a service call... In U.S.A. www.maytag.com/help - In Canada www.maytag.ca Dryer will not run • Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. • Was a regular fuse used? Use a time-delay fuse. • Is the dryer door firmly closed? • Was the Start/Pause button firmly pressed? I_arge loads may require pressing and holding the Start/Pause button for 2-5 seconds. No heat • Has a household fuse blown, or has a circuit breaker tripped? The drum may be turning, but you may not have heat. Replace the fuse or reset the circuit breaker. If the problem continues, ca[[ an electrician. Is it a gas dryer? The gas valve clicking is a normal operating sound. Are the four legs installed, and is the dryer level front to back and side to side? The dryer may vibrate if not properly installed. See the Installation Instructions. Is the clothing knotted or balled up? When balled up, the load will bounce, items and restart the dryer. causing the dryer to vibrate. Separate the load Dryer displaying code message "PF" (power failure), check the following: Was the drying cycle interrupted by a power failure? Depending on the length of the power outage, you may be able to resume the cycle by simply pressing START/PAUSE; otherwise, press POWER/CANCEl. and then start a new drying cycle. • "F" Variable (F1, F2, F20, etc.) service codes: Call for service. Unusual sounds Has the dryer had a period of non-use? If the dryer hasn't been used for a while, there may be a thumping few minutes of operation. sound during the first Is a coin, button or paper clip caught between the drum and front or rear of the dryer? Check the front and rear edges of the drum for small objects. Clean out pockets before laundering.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
2. Open
thedryer
door.
I_ocate
thelightbulbcover
onthebackwall
ofthedryer.
Remove
thescrew
located
intheloweright
corner
ofthecover.
Remove
thecover.
3.Turnbulbcounterclockwise.
Replace
thebulbwitha10-watt
appliance
bulbonly.
Replace
thecover
andsecure
withthescrew.
4. Plug
indryer
orreconnect
power.
First try the solutions
suggested here or visit our
website
and reference
FAQs (Frequently
Asked
Questions)
to possibly avoid the cost of a service call...
In U.S.A.
www.maytag.com/help
- In Canada
www.maytag.ca
Dryer
will
not
run
•
Has a household
fuse blown,
or has a circuit
breaker
tripped?
Replace
the fuse or reset the
circuit
breaker.
If the
problem
continues,
call
an electrician.
•
Was a regular
fuse used?
Use a time-delay
fuse.
•
Is the
dryer
door
firmly
closed?
•
Was
the
Start/Pause
button
firmly
pressed?
I_arge loads
may
require
pressing
and
holding
the
Start/Pause
button
for 2-5
seconds.
No heat
•
Has a household
fuse
blown,
or has a circuit
breaker
tripped?
The drum
may be turning,
but
you
may not
have
heat.
Replace
the fuse or reset the
circuit
breaker.
If the
problem
continues,
ca[[
an electrician.
Unusual
sounds
Is
it
a
gas
dryer?
The gas valve
clicking
is a normal
operating
sound.
Are the
four legs installed,
and
is
the dryer
level front
to back and
side
to
side?
The dryer may vibrate if not properly
installed. See the Installation
Instructions.
Is the clothing
knotted
or balled
up?
When
balled
up,
the
load
will
bounce,
causing
the dryer
to
vibrate.
Separate
the
load
items
and
restart
the
dryer.
Dryer
displaying
code
message
"PF"
(power
failure),
check
the
following:
Was
the drying
cycle
interrupted
by a power
failure?
Depending
on the
length
of the
power
outage,
you
may be able
to
resume
the cycle
by
simply
pressing
START/PAUSE;
otherwise,
press POWER/CANCEl.
and then
start
a new
drying
cycle.
•
"F"
Variable
(F1,
F2, F20,
etc.)
service
codes:
Call for
service.
Has the dryer
had a period
of non-use?
If the
dryer
hasn't
been
used for a while,
there
may
be a thumping
sound
during
the first
few
minutes
of operation.
Is a coin,
button
or paper
clip caught
between
the drum
and
front
or
rear
of the dryer?
Check
the
front
and
rear edges of the
drum
for small
objects.
Clean
out
pockets
before
laundering.