Netgear WFS709TP WFS709TP Setup Manual - Page 185

Limiting the Number of Active Voice Calls, Select VoIP CAC Disconnect Extra Call.

Get Netgear WFS709TP - ProSafe Smart Wireless Controller PDF manuals and user guides
UPC - 606449052336
View all Netgear WFS709TP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 185 highlights

WFS709TP ProSafe Smart Wireless Switch Software Administration Manual Limiting the Number of Active Voice Calls You can limit the number of active voice calls allowed on a radio. This feature is disabled by default. When the disconnect extra call feature is enabled, the system monitors the number of active voice calls, and if the defined threshold is reached, any new calls are disconnected. The AP denies association requests from a device that is on call. You enable this feature in the WLAN configuration. You also need to enable call admission control, which is disabled by default. You can also configure the number of simultaneous calls that a radio can handle on a per-protocol basis. To limit the number of active voice calls: 1. Navigate to the Configuration > Advanced > WLAN > Advanced page. 2. Click Add to add a new location. 3. Enter a location ID in the format building.floor.plan, where each value is an integer. 4. Click Add. 5. Select the General tab. 6. Select VoIP CAC Disconnect Extra Call. 7. Click Apply. 8. Select the 802.11b/g or 802.11a tab to configure radio settings. 9. Scroll to the bottom of the page to display VoIP parameters. 10. Select VoIP Call Admission Control. 11. Configure the Call Capacity for the VoIP protocol if needed. 12. Click Apply. Configuring WFS709TP for Voice v1.0, June 2007 14-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
WFS709TP ProSafe Smart Wireless Switch Software Administration Manual
Configuring WFS709TP for Voice
14-3
v1.0, June 2007
Limiting the Number of Active Voice Calls
You can limit the number of active voice calls allowed on a radio. This feature is disabled by
default. When the disconnect extra call feature is enabled, the system monitors the number of
active voice calls, and if the defined threshold is reached, any new calls are disconnected. The AP
denies association requests from a device that is on call.
You enable this feature in the WLAN configuration. You also need to enable call admission
control, which is disabled by default. You can also configure the number of simultaneous calls that
a radio can handle on a per-protocol basis.
To limit the number of active voice calls:
1.
Navigate to the Configuration > Advanced > WLAN > Advanced page.
2.
Click Add to add a new location.
3.
Enter a location ID in the format
building.floor.plan
, where each value is an integer.
4.
Click Add.
5.
Select the General tab.
6.
Select VoIP CAC Disconnect Extra Call.
7.
Click Apply.
8.
Select the 802.11b/g or 802.11a tab to configure radio settings.
9.
Scroll to the bottom of the page to display VoIP parameters.
10.
Select VoIP Call Admission Control.
11.
Configure the Call Capacity for the VoIP protocol if needed.
12.
Click Apply.