Netgear WFS709TP WFS709TP Setup Manual - Page 82

Start, Viewing the Results, box appears

Get Netgear WFS709TP - ProSafe Smart Wireless Controller PDF manuals and user guides
UPC - 606449052336
View all Netgear WFS709TP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

WFS709TP ProSafe Smart Wireless Switch Software Administration Manual Figure 4-16 Start Click Start to launch the optimizing algorithm. The AP symbols move on the page as RF Plan finds the optimum location for each. The process may take several minutes. You can watch the progress on the status bar of your browser. The algorithm stops when the movement is less than a threshold value calculated based on the number of APs. The threshold value is also displayed in the status bar at the bottom of the browser window. Note: IRM scanning must be enabled for the AP and AM plans to work properly. Enable IRM in the configuration > advanced > radio > page for all the radios. Viewing the Results You can view the results of optimizing algorithm two ways: graphically and in a table of suggested APs. To obtain information about a specific AP, place the cursor over its symbol. An information box appears (Figure 4-17) containing information about the AP's exact location, PHY type, channel, power, and so on. 4-18 v1.0, June 2007 RF Plan

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
WFS709TP ProSafe Smart Wireless Switch Software Administration Manual
4-18
RF Plan
v1.0, June 2007
Start
Click Start to launch the optimizing algorithm. The AP symbols move on the page as RF Plan
finds the optimum location for each.
The process may take several minutes. You can watch the progress on the status bar of your
browser. The algorithm stops when the movement is less than a threshold value calculated based
on the number of APs. The threshold value is also displayed in the status bar at the bottom of the
browser window.
Viewing the Results
You can view the results of optimizing algorithm two ways: graphically and in a table of suggested
APs. To obtain information about a specific AP, place the cursor over its symbol. An information
box appears (
Figure 4-17
) containing information about the AP’s exact location, PHY type,
channel, power, and so on.
Figure 4-16
Note:
IRM scanning must be enabled for the AP and AM plans to work properly. Enable
IRM in the configuration > advanced > radio > page for all the radios.