Netgear WFS709TP WFS709TP Setup Manual - Page 38

Deployment Scenario #2, Data center, Floor 3, subnet, WFS709TP, is default, gateway, for clients - default ip address

Get Netgear WFS709TP - ProSafe Smart Wireless Controller PDF manuals and user guides
UPC - 606449052336
View all Netgear WFS709TP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

WFS709TP ProSafe Smart Wireless Switch Software Administration Manual • Set the IP address of VLAN 1. • Set the default gateway to the IP address of the interface of the upstream router to which you will connect the WFS709TP. 2. Connect the uplink port on the WFS709TP to the switch or router interface. By default, all ports on the WFS709TP are access ports and will carry traffic for a single VLAN. 3. Deploy the APs. The APs will use the ADP protocol to locate the WFS709TP. You would then configure the SSIDs with VLAN 1 as the assigned VLAN for all users. Deployment Scenario #2 Floor 3 subnet Floor 2 subnet Floor 1 subnet Data center Figure 2-2 WFS709TP is default gateway for clients 2-2 Deploying a Basic WFS709TP System v1.0, June 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
WFS709TP ProSafe Smart Wireless Switch Software Administration Manual
2-2
Deploying a Basic WFS709TP System
v1.0, June 2007
•
Set the IP address of VLAN 1.
•
Set the default gateway to the IP address of the interface of the upstream router to which
you will connect the WFS709TP.
2.
Connect the uplink port on the WFS709TP to the switch or router interface. By default, all
ports on the WFS709TP are access ports and will carry traffic for a single VLAN.
3.
Deploy the APs. The APs will use the ADP protocol to locate the WFS709TP.
You would then configure the SSIDs with VLAN 1 as the assigned VLAN for all users.
Deployment Scenario #2
Figure 2-2
Data center
Floor 3
subnet
Floor 2
subnet
Floor 1
subnet
WFS709TP
is default
gateway
for clients