Panasonic Handheld P2 HD Camcorder with AVC-ULTRA Recording Operating Instruct - Page 147
Mode check display, FUNCTION] screen, AUDIO] screen
View all Panasonic Handheld P2 HD Camcorder with AVC-ULTRA Recording manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 147 highlights
Chapter 7 Display - Screen status display No Item Shooting 35 Recording media display l 36 Simultaneous recording mode display l 37 High-sensitivity mode display l 38 One clip recording mode status display l 39 Recording/playback operation status display l 40 switch operation display l 41 GPS display l 42 Audio monitor volume adjustment display l 43 Front audio level volume display l Playback - - - - l : : l - l - l - l - l -*3 - l - - l - l -*1 -*1 - -*1 -*1 : [OTHER DISPLAY] [ALL] l [PARTIAL] l [USER] l l - l l l l l l l l l l l l l l - l -*1 -*1 -*1 -*1 -*1 -*1 *1 May be displayed depending on other settings. *2 Displayed when the remaining capacity becomes smaller. *3 Displayed during shooting. Mode check display The camera settings and status can be displayed on the viewfinder or LCD monitor screen for check. Each time the switch on the camera is pushed towards the side, the five screens are switched. [STATUS] screen display → [FUNCTION] screen display → [AUDIO] screen display → [USER SW] screen display → [META INFO] screen display → no display Each screen is displayed for approximately five seconds. Pushing the switch towards the side while the screen is displayed moves to the next screen. [FUNCTION] screen Displays the video output status and information of the recording media. [SDI OUT] [P2CARD STATUS] [PROXY] [NETWORK] - [TYPE] [CHAR] - [TOTAL P2/mP2] [SLOT1] [SLOT2] [SLOT3] [MEDIA] [MODE] [PROXY ERROR] [NETWORK] Displays the status of the signal output from the terminal. Displays the format of the signal output from the terminal by [HD‑SDI]/ [SD‑SDI]. Displays the superimposition status of characters selected in the main menu → [OUTPUT SEL] → [SDI OUT CHAR] by [ON]/[OFF]. Displays the status of the P2 card inserted in the card slot, remaining capacity, and total used capacity. The statuses of cards to be displayed are as follows: [ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/ [FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD] For details, refer to "P2 card access LEDs and status of P2 cards" (page 35). Displays the remaining capacity/total capacity totaled for slots 1 and 2 (or slots 3) and the recording media ([P2] or [mP2]). Displays the status of the microP2 memory card in slot 1 and remaining capacity/total capacity. Displays the status of the microP2 memory card in slot 2 and remaining capacity/total capacity. Displays the status of the P2 memory card in slot 3 and remaining capacity/total capacity. Displays the media selection status for proxy recording. [P2]/[P2&SD]/[OFF] Displays the setting status for proxy recording mode. [AVC-G6 2CH MOV]/[SHQ 2CH MOV]/[HQ 2CH MOV]/[LOW 2CH MOV] Displays the operation error on the proxy module. Displays the network to be used and its status. [AUDIO] screen Displays audio settings and the selection status of each recording channel. [AUDIO] [A.IN] [INT MIC] [AUDIO OUT] [CH1/2/3/4] Displays the built-in microphone status set in the main menu → [AUDIO SETUP] → [INPUT SETTING] → [INT MIC]. ff[STEREO]: Records audio from two directions in the front with the 2ch stereo microphone. ff[MONO]: This mode records clearer audio from the front by enhancing the directionality forward like a shotgun microphone. Audio recorded on the left and right are the same. ff[OFF]: Disables audio of the built-in microphone. Displays the audio input signal status set in the main menu → [AUDIO SETUP] → [OUTPUT SETTING] → [AUDIO OUT]. [CH1/CH2]/[CH1]/[CH2]/[CH3/CH4]/[CH3]/[CH4] Displays the input status of each channel. [INT(L)]/[INT(R)]/[INPUT1]/[INPUT2] - 147 -