Panasonic SDC615 AJSDC615 User Guide - Page 20

Basic procedures

Get Panasonic SDC615 - AJ Camcorder - 520 KP PDF manuals and user guides
UPC - 791871302699
View all Panasonic SDC615 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Chapter 3 Recording and playback 3-2 Basic procedures This section describes the basic steps for shooting and recording. Before actually departing to shoot scenes, carry out inspections to ensure that the system is functioning properly. * For details on how to perform these inspections, refer to "6-1 Inspections prior to shooting." From providing the power supply to loading the cassette 1 Attach a fully charged battery pack. Up to performing the switch settings Provide the power supply, and load the cassette. Next, set each switch as shown in the figure below, and then proceed to operate. Switch settings for shooting and recording OUTPUT: CAM/AUTO KNEE ON AUDIO SELECT CH 1/CH 2: AUTO 2 Set the POWER switch to ON. Now check that the HUMID display is not showing and that at least 5 segments of the remaining battery charge display are lighted. ≥ If the HUMID display is showing, wait until it goes off. ≥ When five or more segments of the remaining battery charge display have not lighted, first check the battery setting. If there is nothing wrong with the battery setting, replace the existing battery pack with a fully charged battery pack. 3 Check that there are no cables around the cassette holder or top panel, and then press the EJECT button to open the cassette holder. Aperture: Automatic GAIN: Normally set to 0 dB; change to a more suitable value if the picture is too dark. TCG: F-RUN or R-RUN 4 After checking the following points, insert the cassette tape and close the cassette holder. ≥ Position of the accidental erasure prevent tab ≥ Tape slack 3 4 2 2 1 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Chapter 3
Recording and playback
20
3-2 Basic procedures
This section describes the basic steps for shooting and
recording.
Before actually departing to shoot scenes, carry out
inspections to ensure that the system is functioning properly.
* For details on how to perform these inspections, refer to
“
6-1
Inspections prior to shooting.
”
From providing the power supply to loading the
cassette
Up to performing the switch settings
Provide the power supply, and load the cassette.
Next, set
each switch as shown in the figure below, and then proceed
to operate.
1
Attach a fully charged battery pack.
2
Set the POWER switch to ON.
Now check that the
HUMID display is not showing and that at least 5
segments of the remaining battery charge display are
lighted.
≥
If the HUMID display is showing, wait until it goes off.
≥
When five or more segments of the remaining battery
charge display have not lighted, first check the battery
setting.
If there is nothing wrong with the battery
setting, replace the existing battery pack with a fully
charged battery pack.
3
Check that there are no cables around the cassette
holder or top panel, and then press the EJECT button to
open the cassette holder.
4
After checking the following points, insert the cassette
tape and close the cassette holder.
≥
Position of the accidental erasure prevent tab
≥
Tape slack
1
2
2
3
4
Switch settings for shooting and recording
AUDIO SELECT
CH 1/CH 2:
AUTO
TCG:
F-RUN or R-RUN
OUTPUT:
CAM/AUTO KNEE ON
GAIN:
Normally set to 0 dB; change to
a more suitable value if the
picture is too dark.
Aperture:
Automatic