Panasonic SDC615 AJSDC615 User Guide - Page 81
Option Mode
UPC - 791871302699
View all Panasonic SDC615 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 81 highlights
Chapter 7 Menu description tables 7-2-2 OPTION MODE Item/ Data storage Variable range P.OFF GPS DATA HOLD CLEAR CUF COMPONENT OUT OFF BETACAM M2 CUF 1394 TYPE DVCPRO DV CUF 1394 AUDIO IN CH1/CH2 CH3/CH4 CUF 1394 SPEED S100 S200 S400 CUF Remarks For selecting whether or not to hold the UMID GPS position information while the power is off and record the information as the data still held as the previous value until another measurement can be taken after the power is next turned on. HOLD: The data is held and recorded. CLEAR: The data is cleared at the same time as the power is turned off, and all zeros (no information) are recorded from the time the power is turned on until the measurement is next taken. For setting the analog component signal output level. OFF: Output stops during power save. (Note that this setting is forced ON if a camera adapter is connected and a tally signal is detected from pin 26. Otherwise it is OFF.) BETACAM: Output at the ß-CAM level. M2: Output at the M II level. For setting the format of the signals to be output from the DVCPRO connector. DVCPRO: The signals are output in the DVCPRO (25M) format. DV: The signals are output in the DV format. SDC905 The signals are output in the DVCPRO50 format if 16:9/50M or 4:3/50M is selected as the REC MODE menu item setting on the screen. For selecting the channel on which the reception data is to be recorded on the tape when receiving DV format data in the 4CH audio signal mode and recording the data on a DVCPRO (25M) tape. CH1/CH2: The reception data is recorded on CH1 and CH2. CH3/CH4: The reception data is recorded on CH3 and CH4. For setting the transfer speed of the signals to be output from the DVCPRO connector. S100: 100 Mbps S200: 200 Mbps S400: 400 Mbps Item/ Data storage Variable range Remarks 1394 IN CH 0 : 63 AUTO CUF For setting the input channel for the signals to be supplied to the DVCPRO connector. 0-63: The channel is fixed at the specified number. AUTO: The channel corresponding to the setting of the externally connected unit is selected. 1394 OUT CH 0 : 63 AUTO CUF For setting the output channel for the signals to be output from the DVCPRO connector 0-63: The channel is fixed at the specified number. AUTO: The channel corresponding to the setting of the externally connected unit is selected. 26PIN VIDEO SELECT COMPONENT For setting the video signals to be output from VIDEO OUT pin #4 of the 26-pin connector when a 26-pin 7 camera adapter is connected. COMPONENT: The component Y signal is output. VIDEO OUT: The same signal (composite signal) as the CUF VIDEO OUT connector signal is output. 26PIN CONTROL OFF BOTH CUF For setting whether recording is to be controlled by the unit or by both the unit and the external VTR which is connected to the 26-pin camera adapter. OFF: Recording is performed by the unit only. (It is not performed using the external VTR.) BOTH: Recording is performed by both the unit and the external VTR. The tally lamp indicates the status of the tally signal of the 26-pin connector. (The tally lamp setting can be established using REC TALLY in the SYSTEM MODE.) 26PIN CTL DEFAULT NORMAL SPECIAL CUF For setting the control signal of the VTR to be output from pin #12 of the 26-pin connector when using a VTR connected to a 26-pin camera adapter. NORMAL: STOP "low," START "high" (for AJ-D92) SPECIAL: STOP "high," START "low" The underlining in the variable range column indicates the setting in the preset mode. 81