Panasonic SDC615 AJSDC615 User Guide - Page 40

Chapter 4 Adjustments and settings for recording Display item What is displayed 3 Camera warning and message display area (Displays related to the AWB, ABB and switch operations) ABB ACTIVE ABB OK ABB BREAK ABB NG W-SHD ACTIVE W-SHD OK W-SHD BREAK W-SHD NG LVL OVER B-SHD READY (Switch selection displays) B-SHD ACTIVE B-SHD OK B-SHD BREAK B-SHD NG B-SHD LVL OVER WHITE: # ¢.¢K (LOW LIGHT warning display) (Y GET value) AUTO KNEE: ON/OFF GAIN: ¢¢dB SS: 1/¢¢¢¢ SS: 1 1/¢¢¢¢ SS: SUPER V FILTER: ¢ ¢.¢K EXTENDER: ON/OFF IRIS: ¢¢ F ¢ ¢ LOW LIGHT ¢¢¢.¢% (CALL display) (MARKER display) 4 Information allocated to USER buttons UM: USER MAIN U1: USER1 button U2: USER2 button CALL MKR: A/B/OFF INH S.GAIN ¢¢dB/OFF DS.GAIN ¢¢:/OFF S.IRIS ON/OFF I.OVR ON/OFF S.BLK -¢¢/OFF B.STR ON/OFF AUDIO CH1 AUDIO CH2 40 Status when display appears This appears during an ABB operation. This appears when the ABB operation has been completed satisfactorily. This appears when the ABB operation has been forcibly terminated. This appears when the ABB operation has not been completed satisfactorily. This appears during a WHITE SHADING operation. This appears when the WHITE SHADING operation has been completed satisfactorily. This appears when the WHITE SHADING operation has been forcibly terminated. This indicates that white shading has not been completed satisfactorily as the brightness level was excessively high during the WHITE SHADING operation. This appears when the BLACK SHADING operation is ready to be performed as a result of holding down the ABB switch for a length of time during an ABB operation. This appears during a BLACK SHADING operation. This appears when the BLACK SHADING operation has been completed satisfactorily. This appears when the BLACK SHADING operation has been forcibly terminated. This appears when the BLACK SHADING operation has been not completed satisfactorily. This warns the user that the brightness is too high during the BLACK SHADING operation. This appears when the position of the WHITE BAL switch has been changed. "A," "B" or "PRE" appears at #. VAR ¢.¢ K is displayed when channel A, Y is set to VAR. ATW MODE is displayed when ATW is assigned to channel B. This appears when the AUTO KNEE switch has been set to ON or OFF. This appears when the gain has been selected using the GAIN selector switch or USER button. This indicates the shutter speed value when the shutter speed has been selected. This appears when synchro scan has been selected as the shutter speed. This appears when SUPER V has been selected as the shutter speed. This appears when the filter setting has been selected. This appears when the lens extender has been set to ON or OFF. This appears when the iris overwrite correction value has been changed. This appears when the brightness has dropped. With the Y GET ON setting, the output brightness level near the center marker is displayed as "%." This appears when the call command has been issued from the extender. This indicates the type of marker presently being displayed. "INH" is indicated when the operation of the USER button has been disabled. This indicates the value selected for S.GAIN. This indicates the value selected for DS.GAIN. This indicates whether S.IRIS is set to ON or OFF. This appears when the IRIS OVERRIDE setting is enabled (ON). This indicates whether SUPER BLACK is set to ON or OFF and, if it is set to ON, it also indicates its value. This indicates whether BLACK STRETCH (black level gradation compensation) is set to ON or OFF. This appears when the input signal to recorded on audio channel 1 has been switched. This appears when the input signal to recorded on audio channel 2 has been switched.