Samsung NY58J9850WS/AA User Manual - Page 50

Hinge arm, Indentation, Bottom edge of slot, Unlocked position, English, How to re-install the door

Get Samsung NY58J9850WS/AA PDF manuals and user guides View all Samsung NY58J9850WS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Maintenance How to re-install the door You can re-install the upper door the same way you re-install the full door. 1. Firmly grasp both sides of the door at the top. 2. With the door at the same angle as the removal position, slide the indentation of the hinge arm into the bottom edge of the hinge slot. The notch in the hinge arm must be fully inserted into the bottom of the slot. Bottom edge of slot Hinge arm How to remove and re-install the warming drawer. Warming drawer 1. Slide open the drawer until it stops. 2. Locate the roller guide clips on either side. Using both hands, pull down the left clip while lifting the right clip, and then remove the drawer. 3. Clean the drawer in warm, soapy water using a cloth or soft brush. Then, rinse and dry it thoroughly. Indentation 3. Open the door fully. If the door will not open fully, the indentation is not inserted correctly in the bottom edge of the slot. 4. Push the hinge locks up against the front frame of the oven cavity into the locked position. Hinge lock 4. To re-install, put the drawer in the roller guides on either side, and then snap the clips into place. 5. Close the oven door. Unlocked position Locked position Maintenance 50 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
50 English
Maintenance
Maintenance
How to re-install the door
You can re-install the upper door the same way you re-install the full door.
1.
Firmly grasp both sides of the door at the top.
2.
With the door at the same angle as the removal position, slide the indentation
of the hinge arm into the bottom edge of the hinge slot. The notch in the
hinge arm must be fully inserted into the bottom of the slot.
Hinge arm
Indentation
Bottom edge of slot
3.
Open the door fully. If the door will not open fully, the indentation is not
inserted correctly in the bottom edge of the slot.
4.
Push the hinge locks up against the front frame of the oven cavity into the
locked position.
Unlocked position
Hinge lock
Locked position
5.
Close the oven door.
How to remove and re-install the warming drawer.
Warming drawer
1.
Slide open the drawer until it stops.
2.
Locate the roller guide clips on either
side. Using both hands, pull down the
left clip while lifting the right clip, and
then remove the drawer.
3.
Clean the drawer in warm, soapy water
using a cloth or soft brush. Then, rinse
and dry it thoroughly.
4.
To re-install, put the drawer in the
roller guides on either side, and then
snap the clips into place.