Schwinn 490 Elliptical Service Manual - Page 49

ELECTRICAL WIRING ROUTE DETAIL, Resistance Sensor

Get Schwinn 490 Elliptical PDF manuals and user guides View all Schwinn 490 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

LEFT ELECTRICAL WIRING ROUTE DETAIL - Resistance Sensor Speed Sensor Resistance Sensor CABLE ASSEMBLY, HUB to MAST HARNESS CABLE, SPEED SENSOR WIRE ASSY, SPLIT CBL RESISTANCE SENS, SPEED SENSOR, & SERVO SENSOR HUB HANDLE BAR BUTTONS SERVO 9. Re-assemble the machine in the reverse order of when the parts were removed. 10. Plug the power cord into the machine and wall outlet. 11. Power on the machine. After the Power-Up/Welcome screen appears, use the Resistance Level Quick keys 25 and 1 to confirm that the magnet caliper moves properly between resistance level 1 and 25. DC POWER SENSOR HUB LIFT MOTOR CONTROL LIFT CO OFFLINE POWER SUPPLY 12. Final Inspection CABLE, CONNECTOR WIRE POWER Inspect your machine to ensure that all hardware isBRtigOhWt Nand components are propGerNlyDassembled. BLUE Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner's SWITCH Manual. INLET BROWN BLUE BLACK RED WHITE 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
49
SENSOR HUB
SERVO
Resistance Sensor
Speed Sensor
WIRE ASSY, SPLIT CBL
RESISTANCE SENS, SPEED
SENSOR, & SERVO
to MAST HARNESS
CABLE, SPEED SENSOR
LIFT
9.
Re-assemble the machine in the reverse order of when
the parts were removed.
10.
Plug the power cord into the machine and wall outlet.
11.
Power on the machine. After the Power-Up/Welcome
screen appears, use the Resistance Level Quick keys 25
and 1 to confirm that the magnet caliper moves properly
between resistance level 1 and 25.
12.
Final Inspection
Inspect your machine to ensure that all hardware is tight and
components are properly assembled.
Do not use until the machine has been fully
assembled and inspected for correct
performance in accordance with the Owner’s
Manual.
ELECTRICAL WIRING ROUTE DETAIL
- Resistance Sensor