Schwinn 490 Elliptical Service Manual - Page 54

Calibrating the Resistance

Get Schwinn 490 Elliptical PDF manuals and user guides View all Schwinn 490 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

5. Using a 6mm hex wrench, remove the 2 screws (indicated by ovals) that attach the Sensor Hub to the Frame. 6. Remove the old Sensor Hub, and install the new Sensor Hub. Connect all the cables to the Sensor Hub in their proper locations. Be sure not to crimp any cables. 7. Re-install all remaining parts that were removed in reverse order. Calibrating the Resistance: ! Do not use the Console Resistance Quick Keys to set resistance until the calibration process is complete and calibration saved. Note: During the calibration process no one should be pedaling the machine. Standing on the pedals is okay during the calibration process. 8. Plug the power cord into the machine and wall outlet, and flip the power switch to on. Resistance Level Quick 25 button ™ 9. Push the Programs button and hold for 3 seconds while in the Power-Up Mode to go into the Console Setup Mode (System Menu). Note: To exit the System Menu and return to the PowerUp Mode screen, push the Pause/Stop button. 54 Resistance Down button

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
54
5.
Using a 6mm hex wrench, remove the 2 screws
(indicated by ovals) that attach the Sensor Hub to the
Frame.
6.
Remove the old Sensor Hub, and install the new
Sensor Hub. Connect all the cables to the Sensor Hub in
their proper locations. Be sure not to crimp any cables.
7.
Re-install all remaining parts that were removed in
reverse order.
8.
Plug the power cord into the machine and wall outlet,
and flip the power switch to on.
9.
Push the Programs button and hold for 3 seconds while
in the Power-Up Mode to go into the Console Setup Mode
(System Menu).
Note:
To exit the
System Menu and return to the Power-
Up Mode screen, push the Pause/Stop button.
Resistance Level Quick 25 button
Resistance Down button
Calibrating the Resistance:
!
Do not use the Console Resistance Quick Keys to set resistance until the calibration
process is complete and calibration saved.
Note:
During the calibration process no one should be pedaling the machine. Standing on the pedals is okay during the
calibration process.