Schwinn 490 Elliptical Service Manual - Page 65

Replacing the Rear Shroud

Get Schwinn 490 Elliptical PDF manuals and user guides View all Schwinn 490 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Section 3 - Replacing the Rear Shroud 1. If replacing the Rear Shroud, the Incline Arm will need to be released. Using 6mm hex wrench and a 13mm open faced wrench, remove the indicated hardware that attaches the Incline Arm. 2. Slide the Incline (Lift) Motor Arm from the Rail Assembly. In order to avoid possible serious injury, when the Rail Assembly has been released from the Main Assembly, be careful to avoid fingers or hands being caught or pinched. Do not place fingers or hands below any pivoting parts of the Rail Assembly. 3. Using a #2 Phillips screwdriver, remove the 4 screws (2 indicated on this side of the machine by ovals) from the Rear Shroud. Rail Assembly Incline (Lift) Motor Arm 4. Gently pivot the Rear Shroud down along the Incline (Lift) Motor Arm and remove it. Rear Shroud Rear Shroud 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
65
Section 3 - Replacing the Rear Shroud
1.
If replacing the Rear Shroud, the Incline Arm will need
to be released. Using 6mm hex wrench and a 13mm open
faced wrench, remove the indicated hardware that attaches
the Incline Arm.
2.
Slide the Incline (Lift) Motor Arm from the Rail Assembly.
In order to avoid possible serious injury, when the
Rail Assembly has been released from the Main
Assembly, be careful to avoid fingers or hands
being caught or pinched. Do not place fingers or
hands below any pivoting parts of the Rail
Assembly.
3.
Using a #2 Phillips screwdriver, remove the 4 screws (2
indicated on this side of the machine by ovals) from the Rear
Shroud.
4.
Gently pivot the Rear Shroud down along the Incline
(Lift) Motor Arm and remove it.
Incline (Lift)
Motor Arm
Rear
Shroud
Rear
Shroud
Rail Assembly