Sharp AL 1661CS AL-1661CS Facsimile Operation Manual - Page 56

If needed, set the original size

Get Sharp AL 1661CS - B/W Laser - All-in-One PDF manuals and user guides
UPC - 074000074606
View all Sharp AL 1661CS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

HOW TO USE THE FAX FUNCTION When placing the Original on the document glass: 1 Confirm that there are no original(s) in the RSPF, and open the RSPF. 2 Place the original face down on the document glass. Align the original according to the original scale in the illustration below. (Line up the center of the edge of the original with the ( ) mark.) Original scale mark 3 Gently close the RSPF. Note When using the document glass, do not set original(s) in the RSPF. 4 If needed, set the original size, resolution, and contrast. Continue with the "DIALING AND TRANSMITTING" section. 5 Press the [START] key ( ). The set original size appears in the display and then scanning begins. After the [START] key ( ) is pressed, the Note set original size appears in the display. ORIGINAL SIZE 8.5x11 Make sure that the displayed size is the same as the actual original size. (The factory default setting for the original size is "8.5x11".) If the displayed size is not correct, press the [CLEAR ALL] key ( ) to stop operation and then change the original size setting. (See "ORIGINAL SIZE" (p.53)) When faxing from the document glass, if the size of the original is different from the specified size, part of the image may be cut off. 6 If you have more than one original to read into memory, place the next page, and press the [START] key ( ) to read each page. Go to step 7 after the last page has been scanned. 7 Press the [#] key. Transmission begins. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
52
HOW TO USE THE FAX FUNCTION
When placing the Original on the document glass:
1
Confirm that there are no original(s) in
the RSPF, and open the RSPF.
2
Place the original face down on the
document glass. Align the original
according to the original scale in the
illustration below. (Line up the center
of the edge of the original with the
(
) mark.)
3
Gently close the RSPF.
4
If needed, set the original size,
resolution, and contrast. Continue
with the "DIALING AND
TRANSMITTING" section.
5
Press the [START] key (
).
The set original size
appears in the display
and then scanning
begins.
6
If you have more than one original to
read into memory, place the next
page, and press the [START] key (
)
to read each page.
Go to step 7 after the last page has been
scanned.
7
Press the [#] key.
Transmission begins.
When using the document glass, do not set
original(s) in the RSPF.
mark
Original
scale
Note
After the [START] key (
) is pressed, the
set original size appears in the display.
Make sure that the displayed size is the
same as the actual original size. (The
factory default setting for the original size is
"8.5x11".) If the displayed size is not correct,
press the [CLEAR ALL] key (
) to stop
operation and then change the original size
setting. (See "ORIGINAL SIZE" (p.53))
When faxing from the document glass, if the
size of the original is different from the
specified size, part of the image may be cut
off.
Note
ORIGINAL SIZE
8.5x11