Sharp FO-2970M Service Manual - Page 25

FO-2970MU • Soft switch function description SW1 No. 1 ~ No. 4 Recall interval Choice is made for a recall interval for speed, rapid dial numbers, ten key +START and search + START. Use a binary number to program this. If set to 0 accidentally, 1 will be assumed. SW1 No. 5 ~ No. 8 Recall times Choice is made as to how many recall times should be made. Use a binary number to program this. SW2 No. 1 Dial mode Switch the type according to the telephone circuit connected to the facsimile. 0: TONE DIAL 1: PULSE DIAL SW2 No. 2 Reception mode Auto/manual receiving mode is set. SW2 No. 3 ECM mode Used to determine ECM mode function. Refer to the following table. SW2- No. 3 ECM mode SW6- No. 2 MH fixed Compression method ECM MMR mode ECM MR mode ECM MMH mode ECM MH mode MR mode MH mode (Depending on remote machine) 00 0 0000011111111 01 0 1010101010101 Yes No Yes No No No No No No No No No No No No No Yes No Yes No Yes No Yes No No No No No No No No No Yes Yes No No Yes Yes No No No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes SW2 No. 4 CNG detection in stand-by mode The CNG signal detection function during stand-by stops. 0: Yes 1: No SW2 No. 5 Polling security This switch is employed to enable or disable the polling operation using the ID code verification function, in order to prevent unauthorized polling operation. SW2 No. 6 Automatic cover sheet When "0" (=YES) is selected, the cover sheet is automatically sent after transmission of the original to notify the receiver of the number of original sheets transmitted. SW2 No. 7 Junk fax function in manual reception It is set whether JUNK-FAX is functioned in the manual receiving mode or not. SW2 No. 8 Anti junk fax function This function is used to receive data from a specific remote machine (station registered in entry mode). It is the function that refused a reception in the case that TSI of remote machine matched with fax number of the station registered. 0: No 1: Yes SW3 No. 1 ~ No. 4 Number of rings for auto receive When the machine is set in the auto receive mode, the number of rings before answering can be selected. It may be set from one to nine rings using a binary number. If the soft switch was set to 1, a direct connection is made to the facsimile. If it was set to 0 accidentally, receive ring is set to 1. If it was above 9, receive rings are set to 9. SW3 No. 5 ~ No. 8 Automatic switching manual to auto receive mode (0: OFF) This setting allows machine to switch from manual to Auto Receive mode. Setting this number to 0 forces machine to stay in Manual receive mode. Entering the binary number 0 forces the machine to remain in the manual answer mode. If a number between 1 and 9 is entered, the machine will go into the answer mode after the given number of rings. However, it can be used as an ordinary telephone if the handset is taken off the hook before this programmed number is finished. If entry of a number above 9 by accident, it will be set to 9. In this case, it must be corrected to the proper number. SW4 No. 1 ~ No. 3 Communication results printout (transaction report) Every communication, the result can be output. As usual, it is set to print the timer sending communication error alone. If No.1 : 1 No.2 : 1 No.3 : 0 are set, printing is always on (printed ever if it is normally ended). 000 : Error, timer and memory sending/receiving 010 : Sending 110 : Continuous printing 100 : Not printed 001 : Communication error SW4 No. 4 Delay timer before line connect in auto dial Delay time between the dial key input and line connection under the auto dial mode. SW4 No. 5, No. 6 Delay timer of after line connect in auto dial Delay time between the line connection and dial data output under the auto-dial mode. SW4 No. 7, No. 8 Number of CNG detect (STAND-BY mode) Used for detection of CNG in 1 to 4 pulses. SW5 No. 1 Time format When this switch is set to "0", time is displayed in 12-hour system. When set to "1", 24-hour system. 2 - 21