Sharp FO-2970M Service Manual - Page 32

] Error code table

Get Sharp FO-2970M PDF manuals and user guides View all Sharp FO-2970M manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

FO-2970MU [4] Error code table 1. Communication error code table G3 Transmission Code 0 Final received signal Incomplete signal frame Error Condition (Receiver side) Cannot recognize bit stream after flag 1 NSF, DIS 2 CFR 3 FTT 4 MCF 5 PIP or PIN Cannot recognize DCS signal by echo etc. Cannot recognize NSS signal (FIF code etc) Disconnects line during reception (carrier missing etc) Disconnects line by fallback Disconnects line during reception of multi page Cannot recognize NSS, DCS signal in the case of mode change The line is hung up without replying to telephone request from the receiving party. 6 RTN or RTP 7 No signal or DCN 8 − 11 − 12 − 13 − Cannot recognize NSS, DCS signal after transmit RTN or RTP signal. No response on receiver side or DCN signal received* (transmitter side) Owing to error in some page the error could not be corrected although the specified number of error retransmission was attempted. Error occurred after or while reception by the remote (receiving) machine was revealed to be impossible. Error occurred just after fallback. Error occurred after a response to retransmission end command was received. G3 Reception Code 0 Final received signal Incomplete signal frame Error Condition (Receiver side) Cannot recognize bit stream after flag 1 NSS, DCS 2 NSC, DTC 3 EOP 4 EOM 5 MPS 6 PR1-Q 7 No signal or DCN 8 − 9 − 10 − 11 − 12 − 13 − 14 − Cannot recognize CFR or FTT signal Disconnects line during transmission (line error) Cannot recognize NSS signal (FIF code etc) Cannot recognize MCF, PIP, PIN, RTN, RTP signal Cannot recognize MCF, PIP, PIN, RTN, RTP signal in the case of mode change The line is hung up without replying to communication request. Cannot recognize PIP, PIN signal in the case of TALK request No response in transmitter (cannot recognize DIS signal) or DCN signal received* (receiver side) Error occurred upon completion of reception of all pages. Error occurred when mode was changed or Transmission/Reception switching was performed. Error occurred during partial page or physical page reception. Error occurred after or during inquiry from the remote (transmitting) machine as to whether reception is possible or not. Error occurred during or just after fallback. Error occurred after the retransmission end command was received. Error occurred after the voice communication command was received. 2 - 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
FO-2970MU
2 – 28
[4] Error code table
1. Communication error code table
G3 Transmission
Code
Final received signal
Error Condition (Receiver side)
0
Incomplete signal frame
Cannot recognize bit stream after flag
1
NSF, DIS
Cannot recognize DCS signal by echo etc.
Cannot recognize NSS signal (FIF code etc)
2
CFR
Disconnects line during reception (carrier missing etc)
3
FTT
Disconnects line by fallback
4
MCF
Disconnects line during reception of multi page
Cannot recognize NSS, DCS signal in the case of mode change
5
PIP or PIN
The line is hung up without replying to telephone request from the receiving party.
6
RTN or RTP
Cannot recognize NSS, DCS signal after transmit RTN or RTP signal.
7
No signal or DCN
No response on receiver side or DCN signal received* (transmitter side)
8
-
Owing to error in some page the error could not be corrected although the specified number of
error retransmission was attempted.
11
-
Error occurred after or while reception by the remote (receiving) machine was revealed to be
impossible.
12
-
Error occurred just after fallback.
13
-
Error occurred after a response to retransmission end command was received.
G3 Reception
Code
Final received signal
Error Condition (Receiver side)
0
Incomplete signal frame
Cannot recognize bit stream after flag
1
NSS, DCS
Cannot recognize CFR or FTT signal
Disconnects line during transmission (line error)
2
NSC, DTC
Cannot recognize NSS signal (FIF code etc)
3
EOP
Cannot recognize MCF, PIP, PIN, RTN, RTP signal
4
EOM
Cannot recognize MCF, PIP, PIN, RTN, RTP signal in the case of mode change
5
MPS
The line is hung up without replying to communication request.
6
PR1-Q
Cannot recognize PIP, PIN signal in the case of TALK request
7
No signal or DCN
No response in transmitter (cannot recognize DIS signal) or DCN signal received* (receiver side)
8
-
Error occurred upon completion of reception of all pages.
9
-
Error occurred when mode was changed or Transmission/Reception switching was performed.
10
-
Error occurred during partial page or physical page reception.
11
-
Error occurred after or during inquiry from the remote (transmitting) machine as to whether
reception is possible or not.
12
-
Error occurred during or just after fallback.
13
-
Error occurred after the retransmission end command was received.
14
-
Error occurred after the voice communication command was received.