Singer 7285Q Patchwork Instruction Manual - Page 22

Threading The Top Thread

Get Singer 7285Q Patchwork PDF manuals and user guides View all Singer 7285Q Patchwork manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

THREADING THE TOP THREAD A. Raise the presser foot lifter. Always be sure to raise the presser foot lifter before threading the top thread. (If the presser foot lifter is not raised, correct thread tension cannot be obtained.) B. Turn the hand wheel toward you until the needle is in its highest position. &7KUHDGWKHPDFKLQHZLWK\RXUOHIWKDQGZKLOH¿UPO\JULSSLQJ the thread with your right hand in the following order as illustrated. * Guide the thread through thread guide (1), and then pull it into the pre-tension guide (2). * Pull the thread into the tension discs (which are located LQVLGHWKHPDFKLQH E\¿UVWSDVVLQJWKHWKUHDGWRWKHOHIW of plate (2). Then guide the thread to the bottom of the groove. * Do a U-turn around the inside of the tab (3). 4 * Pass the thread through the thread take-up (4) from right to left. * Pull the thread into the inside of the take-up lever until it reaches the eye of the lever. * Guide the thread into the thread guide (5). * Pass the thread through the eye of the needle (6) from front to back. (See following page for instructions on operation of the Automatic Needle Threader.) IMPORTANT: To verify that the machine is threaded properly in the tension discs, do this simple check: 1.) With the presser foot raised and the needle unthreaded, pull the thread. You should detect only a slight resistance and little or no deÀection of the needle. 2.) Now lower the presser foot and again pull the thread towards the the back of the machine. This time you should detect a considerable amount of resistance and much more deflection of the needle. If you do not detect the resistance, this means you have not threaded the machine correctly and 3 need to rethread it. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
20
4
3
B.
Turn the hand wheel toward you until the needle is in its
highest position.
&µ 7KUHDG WKH PDFKLQH ZLWK \RXU OHIW KDQG ZKLOH ¿UPO\ JULSSLQJ
the thread with your right hand in the following order as
illustrated.
* Guide the thread through thread guide (1), and then pull
it into the pre-tension guide (2).
* Pull the thread into the tension discs (which are located
LQVLGH WKH PDFKLQHÂ E\ ¿UVW SDVVLQJ WKH WKUHDG WR WKH OHIW
of plate (2). Then guide the thread to the bottom of the
groove.
* Do a U-turn around the inside of the tab (3).
* Pass the thread through the thread take-up (4) from right
to left.
* Pull the thread into the inside of the take-up lever until it
reaches the eye of the lever.
* Guide the thread into the thread guide (5).
* Pass the thread through the eye of the needle (6) from
front to back. (See following page for instructions on
operation of the Automatic Needle Threader.)
THREADING THE TOP THREAD
A.
Raise the presser foot lifter. Always be sure to raise the
presser foot lifter before threading the top thread. (If the
presser foot lifter is not raised, correct thread tension
cannot be obtained.)
IMPORTANT:
To verify that the machine is threaded
properly in the tension discs, do this simple
check:
1.) With the presser foot raised and the
needle unthreaded, pull the thread. You
should detect only a slight resistance
and little or no de
À
ection of the needle.
2.) Now lower the presser foot and again
pull the thread towards the the back
of the machine. This time you should
detect a considerable amount of
resistance and much more deflection
of the needle. If you do not detect the
resistance, this means you have not
threaded the machine correctly and
need to rethread it.