Sony DSX-S210X Operating Instructions - Page 19

Playing back via the USB (external) connector, Removing the iPod

Get Sony DSX-S210X PDF manuals and user guides View all Sony DSX-S210X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

7 Press (SOURCE/OFF) repeatedly until "USB" appears, and then press (MODE) to switch the USB device. "USB Internal" appears. The iPod will turn on automatically, and the display will appear on the iPod screen as below.* 2 Connect the iPod to the USB connector via the dock connector to USB cable. The tracks on the iPod start playing automatically from the point last played. If an iPod is already connected, repeat step 7. ("iPod" appears in the display when iPod is recognized.) * Display differs depending on the iPod, or may not appear in the case of an iPod touch being connected. 8 Adjust the volume. Press and hold (SOURCE/OFF) for 1 second to stop playback. Removing the iPod 1 Stop the iPod playback. 2 Press (OPEN). 3 Press PUSH OPEN on the TUNE TRAY. 4 Remove the iPod. 5 Slide in the TUNE TRAY, and close the front panel. Playing back via the USB (external) connector Before connecting the iPod, turn down the volume of the unit. 1 Slide the USB cover. 3 Press (SOURCE/OFF) repeatedly until "USB" appears, and then press (MODE) to switch the USB device. "USB External" appears. The iPod will turn on automatically, and the display will appear on the iPod screen as below.* Tip We recommend the RC-100IP USB cable (not supplied) to connect the dock connector. The tracks on the iPod start playing automatically from the point last played. If an iPod is already connected, to start playback, repeat step 3. ("iPod" appears in the display when iPod is recognized.) * In the case of an iPod touch or iPhone being connected, or that the iPod was last played back using passenger control, the logo will not appear on the screen. 4 Adjust the volume. Press and hold (SOURCE/OFF) for 1 second to stop playback. Removing the iPod 1 Stop the iPod playback. 2 Remove the iPod. Caution for iPhone When you connect an iPhone via USB, telephone volume is controlled by iPhone itself. In order to avoid sudden loud sound after a call, do not increase the volume on the unit during a telephone call. continue to next page t 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
19
7
Press
(SOURCE/OFF)
repeatedly until
“USB” appears, and then press
(MODE)
to switch the USB device.
“USB Internal” appears.
The iPod will turn on automatically, and the
display will appear on the iPod screen as
below.*
The tracks on the iPod start playing
automatically from the point last played.
If an iPod is already connected, repeat step 7.
(“iPod” appears in the display when iPod is
recognized.)
*
Display differs depending on the iPod, or may not
appear in the case of an iPod touch being
connected.
8
Adjust the volume.
Press and hold
(SOURCE/OFF)
for 1 second to
stop playback.
Removing the iPod
1
Stop the iPod playback.
2
Press
(OPEN)
.
3
Press PUSH OPEN on the TUNE TRAY.
4
Remove the iPod.
5
Slide in the TUNE TRAY, and close the front
panel.
Playing back via the USB (external)
connector
Before connecting the iPod, turn down the
volume of the unit.
1
Slide the USB cover.
2
Connect the iPod to the USB
connector via the dock connector to
USB cable.
3
Press
(SOURCE/OFF)
repeatedly until
“USB” appears, and then press
(MODE)
to switch the USB device.
“USB External” appears.
The iPod will turn on automatically, and the
display will appear on the iPod screen as
below.*
Tip
We recommend the RC-100IP USB cable (not
supplied) to connect the dock connector.
The tracks on the iPod start playing
automatically from the point last played.
If an iPod is already connected, to start
playback, repeat step 3. (“iPod” appears in
the display when iPod is recognized.)
*
In the case of an iPod touch or iPhone being
connected, or that the iPod was last played back
using passenger control, the logo will not appear on
the screen.
4
Adjust the volume.
Press and hold
(SOURCE/OFF)
for 1 second to
stop playback.
Removing the iPod
1
Stop the iPod playback.
2
Remove the iPod.
Caution for iPhone
When you connect an iPhone via USB, telephone
volume is controlled by iPhone itself. In order to avoid
sudden loud sound after a call, do not increase the
volume on the unit during a telephone call.
continue to next page
t