Sony PEGA-WL100 Operating Instructions - Page 36

Move your CLI, access point to its factory default setting

Get Sony PEGA-WL100 - Wireless LAN Card PDF manuals and user guides
UPC - 027242617728
View all Sony PEGA-WL100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Symptom The data transfer rate is slow. You forget a WEP (encryption) key. You cannot send or receive email. You cannot perform a HotSync operation. You cannot browse homepages. Cause/Remedy • There is an obstacle that could block off radio waves (e.g., metal plate, concrete block) between your CLIÉ handheld and the access point. p Move your CLIÉ handheld and/or the access point to a different place. p Disable the power saving mode. (This will increase the power consumption. Be careful of the remaining battery power). • There is a device operating at the 2.4 GHz band of frequencies (microwave oven, Bluetooth-enabled device, etc.) around the CLIÉ handheld. p Increase the distance between the device and the CLIÉ handheld or turn off the power of the device. p After changing all the settings of the access point to its factory default setting, set the access point again. To restore the default settings, see the operating instructions of the access point. p Check the settings of the emailing software you are using. For details on how to set the emailing software, see its operating instructions. p Check the settings of HotSync. For details on how to set HotSync, see the operating instructions supplied with your CLIÉ handheld. p Check the settings of the web browser you are using. For details on how to set the web browser, see its operating instructions. Tip You can view the data of the communication preferences. While performing communications using your CLIÉ handheld in which this Wireless LAN card is inserted, show the [Network] screen of [Preferences]. Select [Option] on the menu, then select [View Log]. 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
36
Symptom
The data transfer rate is
slow.
You forget a WEP
(encryption) key.
You cannot send or
receive email.
You cannot perform a
HotSync operation.
You cannot browse
homepages.
Cause/Remedy
•
There is an obstacle that could block off
radio waves (e.g., metal plate, concrete
block) between your CLI
É
handheld and
the access point.
p
Move your CLI
É
handheld and/or the
access point to a different place.
p
Disable the power saving mode.
(This will increase the power
consumption. Be careful of the
remaining battery power).
•
There is a device operating at the 2.4 GHz
band of frequencies (microwave oven,
Bluetooth-enabled device, etc.) around
the CLI
É
handheld.
p
Increase the distance between the
device and the CLI
É
handheld or turn
off the power of the device.
p
After changing all the settings of the
access point to its factory default setting,
set the access point again.
To restore the default settings, see the
operating instructions of the access point.
p
Check the settings of the emailing
software you are using.
For details on how to set the emailing
software, see its operating instructions.
p
Check the settings of HotSync.
For details on how to set HotSync, see the
operating instructions supplied with your
CLI
É
handheld.
p
Check the settings of the web browser
you are using.
For details on how to set the web
browser, see its operating instructions.
Tip
You can view the data of the communication preferences.
While performing communications using your CLI
É
handheld in which this
Wireless LAN card is inserted, show the [Network] screen of [Preferences].
Select [Option] on the menu, then select [View Log].