Symphonic CSC313E Owner's Manual - Page 9

Preparation For Use

Page 9 highlights

PREPARATION FOR USE ANTENNA/CABLE CONNECTIONS Plug the incoming cable into the ANT. jack on the rear of the unit. If your cable service supplies you with a converter box or if you use a satellite system, connect the box with this unit as shown below. Cable TV signal or Antenna Incoming cable from home Antenna / Cable Company (No Cable Box) Cable Box or OR Satellite Box* IN OUT ANT. Rear of the unit ANT. Incoming cable from Cable Company or Satellite Antenna *NOTE (DO NOT DISCONNECT FROM BOX) Some cable TV systems use scrambled signals and require a special converter to receive these channels. Consult your local cable company. Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. NOTE: Before plugging the antenna into the ANT. jack of the unit, check that the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the ANT. jack of the unit. Bent pin Rod Antenna Connection: You can use the Rod Antenna (supplied) if incoming cable is not available. Rod Antenna (Supplied) Cable Plug (Needs to be straightened) (Straight pin) ANT. ANT. For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack before moving the unit. -9- EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56

- 9 -
EN
PREPARATION FOR USE
ANTENNA/CABLE CONNECTIONS
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding
system of the building as close to the point of cable entry as practical.
Plug the incoming cable into the ANT. jack on the rear of the unit.
If your cable service supplies you with a converter box or if you use a satellite system, connect the box with
this unit as shown below.
Cable
TV signal
Antenna
or
ANT.
IN
OUT
Rod Antenna
(Supplied)
Rod Antenna Connection:
You can use the Rod Antenna
(supplied) if incoming cable
is not available
.
ANT.
NOTE:
Before plugging the antenna into the ANT. jack of the
unit, check that the pin is not bent. If it is bent, straighten
the pin as illustrated, then plug the pin into the ANT.
jack of the unit.
For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack
before moving the unit.
Bent pin
Cable
Plug
(Needs to be
straightened)
(Straight pin)
Rear of the unit
*NOTE (DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled signals and
require a special converter to receive these channels.
Consult your local cable company.
OR
Incoming cable from home Antenna /
Cable Company (No Cable Box)
Incoming cable from Cable Company
or Satellite Antenna
Cable Box or
Satellite Box*