TRENDnet TFM-560PCI Manual - Page 18

A3.2.1.3 &F - Set to Factory-Defined Configuration

Get TRENDnet TFM-560PCI PDF manuals and user guides View all TRENDnet TFM-560PCI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

I101 V.90 PCI MODEM USER'S MANUAL 3 Selects auto reliable mode and forces &Q5 (the modem will try to negotiate an error corrected link). This operates the same as \N2 except failure to make a reliable connection results in the modem falling back to the speed buffered normal mode. 4 Selects LAPM error-correction mode and forces &Q5 (the modem will try to negotiate an error corrected link). Failure to make an LAPM error-correction connection results in the modem hanging up. 5 Selects MNP error-correction mode and forces &Q5 (the modem will try to negotiate an error corrected link). Failure to make an MNP error-correction connection results in the modem hanging up. A3.2.1.3 &F - Set to Factory-Defined Configuration This command instructs the modem to set all parameters to factory default values defined in the product Configu- ration Table. The modem loads the factory default configuration (profile). The factory defaults are identified for each command and in the S-Parameter descriptions. A configuration (profile) consists of a subset of S-Parameters. A3.2.1.4 &T [] - Local Analog Loopback Test The modem will perform the local analog loopback test if &T1 is selected. The test can be run only when in an asynchronous operation in non-error-correction mode (normal). To terminate the test in progress, the escape sequence must be entered first. If S18 is non-zero, the test will terminate automatically after the time specified by S18 and the OK result code will be reported. Defined Values Decimal number corresponding to the selected value. 0 Terminates test in progress. 1 Initiates local analog loopback, V.54 Loop 3. If a connection exists when this command is issued, the modem hangs up. The CONNECT XXXX message is displayed upon the start of the test. A2.2.1.5 I [] - Request Identification Information This command causes the modem to report one or more lines of product information text as provided by the Product Configuration File, as selected by the subparameter, followed by a final result code. Defined Values Decimal number corresponding to the selected information. 0 0 report. ... 7 7 report. 9 9 report. A2.2.1.6 +GMI - Request Manufacturer Identification This command causes the modem to report the modem product manufacturer as provided by the Product Configuration File. A2.2.1.7 +GMM - Request Model Identification This command causes the modem to report the modem product model as provided by the Product Configuration File. P.18 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
I101 V.90 PCI MODEM USER'S MANUAL
44
P.18
3
Selects auto reliable mode and forces &Q5 (the modem will try to negotiate an error corrected link).
This operates the same as \N2 except failure to make a reliable connection results in the modem falling
back to the speed buffered normal mode.
4
Selects LAPM error-correction mode and forces &Q5 (the modem will try to negotiate an error cor-
rected link). Failure to make an LAPM error-correction connection results in the modem hanging up.
5
Selects MNP error-correction mode and forces &Q5 (the modem will try to negotiate an error cor-
rected link). Failure to make an MNP error-correction connection results in the modem hanging up.
A3.2.1.3 &F - Set to Factory-Defined Configuration
This command instructs the modem to set all parameters to factory default values defined in the product Configu-
ration Table. The modem loads the factory default configuration (profile). The factory defaults are identified for each
command and in the S-Parameter descriptions. A configuration (profile) consists of a subset of S-Parameters.
A3.2.1.4 &T
[<value>]
- Local Analog Loopback Test
The modem will perform the local analog loopback test if &T1 is selected. The test can be run only when in an
asynchronous operation in non-error-correction mode (normal). To terminate the test in progress, the escape se-
quence must be entered first. If S18 is non-zero, the test will terminate automatically after the time specified by S18 and
the OK result code will be reported.
Defined Values
<value> Decimal number corresponding to the selected value.
0
Terminates test in progress.
1
Initiates local analog loopback, V.54 Loop 3. If a connection exists when this command is issued, the
modem hangs up. The CONNECT XXXX message is displayed upon the start of the test.
A2.2.1.5 I
[<value>]
- Request Identification Information
This command causes the modem to report one or more lines of product information text as provided by the
Product Configuration File, as selected by the <value> subparameter, followed by a final result code.
Defined Values
<value> Decimal number corresponding to the selected information.
0
<value> 0 report.
…
7
<value> 7 report.
9
<value> 9 report.
A2.2.1.6 +GMI - Request Manufacturer Identification
This command causes the modem to report the modem product manufacturer as provided by the Product
Configuration File.
A2.2.1.7 +GMM - Request Model Identification
This command causes the modem to report the modem product model as provided by the Product Configuration
File.