TRENDnet TFM-560PCI Manual - Page 26

Select Pulse Dial Make/Break Ratio

Get TRENDnet TFM-560PCI PDF manuals and user guides View all TRENDnet TFM-560PCI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

I101 V.90 PCI MODEM USER'S MANUAL A2.2.3.6 O[] - Return to On-Line Data Mode This command specifies that the modem will enter the on-line data mode from the on-line command mode with or without a retrain. If in the off-line command mode when this command is entered, the modem reports ERROR. Defined Values Decimal number corresponding to the selected option. 0 Enters on-line data mode from the on-line command mode without a retrain. Handling is determined by the Call Establishment task. Generally, if a connection exists, this command connects the DTE back to the remote modem after an escape (+++). 1 Performs a retrain then enters on-line data mode from the on-line command mode. A2.2.3.7 L[] - Speaker Volume This command sets the speaker volume control according to the parameter supplied. Defined Values Decimal number corresponding to the selected option. 0 Off. 1 Low volume. (Default.) 2 Medium volume. 3 High volume. A2.2.3.8 M[] - Speaker Control This command controls speaker on or off according to the supplied parameter. Defined Values Decimal number corresponding to the selected option. 0 Speaker off. 1 Speaker on during call establishment, but off when receiving carrier. (Default.) 2 Speaker on. 3 Speaker is off when receiving carrier and during dialing, but on during answering. A2.2.3.9 &G[] - Select Guard Tone This command is included for compatibility only and has no effect other than returning an OK result code. Defined Values Decimal number corresponding to the selected option. 0 Included for compatibility only and has no effect other than returning an OK result code. (Default.) 1 Included for compatibility only and has no effect other than returning an OK result code. 2 Included for compatibility only and has no effect other than returning an OK result code. A2.2.3.10 &P[] - Select Pulse Dial Make/Break Ratio This command determines the make/break ratio used during pulse dialing. It is only effective if the appropriate bit to enable this command is set through the Product Configuration File. If enabled, it will override the make/break ratios in the OEM parameters in the Product Configuration File. The default is country-dependent. P.26 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
I101 V.90 PCI MODEM USER'S MANUAL
44
P.26
A2.2.3.6 O
[<value>]
- Return to On-Line Data Mode
This command specifies that the modem will enter the on-line data mode from the on-line command mode with or
without a retrain. If in the off-line command mode when this command is entered, the modem reports ERROR.
Defined Values
<value> Decimal number corresponding to the selected option.
0
Enters on-line data mode from the on-line command mode without a retrain. Handling is determined by
the Call Establishment task. Generally, if a connection exists, this command connects the DTE back to the
remote modem after an escape (+++).
1
Performs a retrain then enters on-line data mode from the on-line command mode.
A2.2.3.7 L
[<value>]
- Speaker Volume
This command sets the speaker volume control according to the parameter supplied.
Defined Values
<value> Decimal number corresponding to the selected option.
0
Off.
1
Low volume. (Default.)
2
Medium volume.
3
High volume.
A2.2.3.8 M
[<value>]
- Speaker Control
This command controls speaker on or off according to the supplied parameter.
Defined Values
<value> Decimal number corresponding to the selected option.
0
Speaker off.
1
Speaker on during call establishment, but off when receiving carrier. (Default.)
2
Speaker on.
3
Speaker is off when receiving carrier and during dialing, but on during answering.
A2.2.3.9 &G
[<value>]
- Select Guard Tone
This command is included for compatibility only and has no effect other than returning an OK result code.
Defined Values
<value> Decimal number corresponding to the selected option.
0
Included for compatibility only and has no effect other than returning an OK result code. (Default.)
1
Included for compatibility only and has no effect other than returning an OK result code.
2
Included for compatibility only and has no effect other than returning an OK result code.
A2.2.3.10 &P
[<value>]
- Select Pulse Dial Make/Break Ratio
This command determines the make/break ratio used during pulse dialing. It is only effective if the appropriate bit
to enable this command is set through the Product Configuration File. If enabled, it will override the make/break ratios in
the OEM parameters in the Product Configuration File. The default is country-dependent.