TRENDnet TFM-560PCI Manual - Page 35

Ring 2, No Carrier 3, Error 4, No Dialtone 6, Busy 7, No Answer 8, Delayed 24, Blacklisted 32, Data

Get TRENDnet TFM-560PCI PDF manuals and user guides View all TRENDnet TFM-560PCI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

I101 V.90 PCI MODEM USER'S MANUAL RING (2) The modem sends this result code when incoming ringing is detected on the line. What qualifies as a ring signal is determined by country-dependent parameters, modifiable through the Product Configuration File. NO CARRIER (3) The modem sends this result code when an attempt o establish a connection fails or an established connection has been terminated.Under X0, if busy tone detection is enforced, this result code is used as a response to the detection of busy or circuit busy. Under X0, if dial tone detection is enforced or selected, this result code indicates that dial tone has not been detected. ERROR (4) The modem returns this result code if the command is not recognized (e.g., the command line has a syntax error or the command is not supported), the command line maximum length is exceeded, a parameter value is invalid, or other problem with processing the command line is detected. Under X0, X1, X2, and X3, this result is used instead of DELAYED and BLACKLISTED. NO DIALTONE (6) For X2 and X4, the modem sends this result code if it has been instructed to wait for dial tone during dialing but none is received. BUSY (7) For X3 and X4, if busy tone detection is enforced, the modem sends this result code when attempting to originate a call if the busy (engaged) signal is detected on the line. NO ANSWER (8) The modem sends this result code when: 1. Attempting to originate a call if a continuous ringback signal is detected on the line until the expiration of the timer S7. 2. "@" (Wait for Quiet Answer) dial modifier was used, but remote ringing followed by five seconds of silence was not detected before expiration of the connection timer (S7) DELAYED (24) For X4, the modem returns this result code when a call fails to connect and the number dialed is considered 'delayed' due to country blacklisting requirements. BLACKLISTED (32) For X4, the modem returns this result code when a call fails to connect and the number dialed is considered 'blacklisted'. DATA (35) The modem returns this result code when a data modem connection is established in a facsimile mode. +FCERROR (+F4) This message is sent to the DTE when high speed fax data (V.27, V.29, V.33, or V.17) is expected and a V.21 signal is received. P.35 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
I101 V.90 PCI MODEM USER'S MANUAL
44
P.35
RING (2)
The modem sends this result code when incoming ringing is detected on the line. What qualifies as a ring signal
is determined by country-dependent parameters, modifiable through the Product Configuration File.
NO CARRIER (3)
The modem sends this result code when an attempt o establish a connection fails or an established connection
has been terminated.Under X0, if busy tone detection is enforced, this result code is used as a response to the
detection of busy or circuit busy. Under X0, if dial tone detection is enforced or selected, this result code
indicates that dial tone has not been detected.
ERROR (4)
The modem returns this result code if the command is not recognized (e.g., the command line has a syntax error
or the command is not supported), the command line maximum length is exceeded, a parameter value is invalid,
or other problem with processing the command line is detected.
Under X0, X1, X2, and X3, this result is used instead of DELAYED and BLACKLISTED.
NO DIALTONE (6)
For X2 and X4, the modem sends this result code if it has been instructed to wait for dial tone during dialing but
none is received.
BUSY (7)
For X3 and X4, if busy tone detection is enforced, the modem sends this result code when attempting to originate
a call if the busy (engaged) signal is detected on the line.
NO ANSWER (8)
The modem sends this result code when:
1. Attempting to originate a call if a continuous ringback signal is detected on the line until the expiration of the
timer S7.
2. “@” (Wait for Quiet Answer) dial modifier was used, but remote ringing followed by five seconds of silence
was not detected before expiration of the connection timer (S7)
DELAYED (24)
For X4, the modem returns this result code when a call fails to connect and the number dialed is considered
‘delayed’ due to country blacklisting requirements.
BLACKLISTED (32)
For X4, the modem returns this result code when a call fails to connect and the number dialed is considered
‘blacklisted’.
DATA (35)
The modem returns this result code when a data modem connection is established in a facsimile mode.
+FCERROR (+F4)
This message is sent to the DTE when high speed fax data (V.27, V.29, V.33, or V.17) is expected and a V.21
signal is received.