Weider 9900i Uk Manual - Page 22

Route the Low Cable 43 under a Pulley 69.

Get Weider 9900i PDF manuals and user guides View all Weider 9900i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

36. Insert a Pulley (69) under the High Cable (44) in the location shown. 36 Attach the Pulley (69) and a Cable Trap (71) to the left side of the Top Frame (6) with an M10 x 93mm Bolt (63), an M10 Washer (88), and an M10 Locknut (74). Make sure that the Cable Trap is oriented to hold the High Cable in the groove of the Pulley. Make sure to leave slack in the High Cable (44) in the indicated location. 37. Insert a Pulley (69) into the loop of the High Cable (44) as shown. 37 Orient two Pulley Plates (70) as shown. Using the second hole in the Pulley Plates (70), attach the Pulley Plates to the Pulley (69) with an M10 x 43mm Bolt (65) and an M10 Locknut (74). 74 88 6 44 69 71 63 Slack 44 65 74 69 70 38. Route the Low Cable (43) under a Pulley (69). Attach the Pulley (69) and a Cable Trap (71) to the left side of the Upright (5) with an M10 x 97mm Bolt (100), two Half Guards (72), an M10 Washer (88) and an M10 Locknut (74). Make sure that the Cable Trap is oriented to hold the Low Cable in the groove of the Pulley. 38 74 88 5 72 69 43 71 72 100 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
22
36
37
37. Insert a Pulley (69) into the loop of the High
Cable (44) as shown.
Orient two Pulley Plates (70) as shown.
Using the second hole in the Pulley Plates (70),
attach the Pulley Plates to the Pulley (69) with
an M10 x 43mm Bolt (65) and an M10 Locknut
(74).
44
65
69
63
71
88
74
74
36. Insert a Pulley (69) under the High Cable (44) in
the location shown.
Attach the Pulley (69) and a Cable Trap (71) to
the left side of the Top Frame (6) with an M10 x
93mm Bolt (63), an M10 Washer (88), and an
M10 Locknut (74).
Make sure that the Cable
Trap is oriented to hold the High Cable in
the groove of the Pulley.
Make sure to leave slack in the High Cable
(44) in the indicated location.
6
69
44
70
38
38. Route the Low Cable (43) under a Pulley (69).
Attach the Pulley (69) and a Cable Trap (71) to
the left side of the Upright (5) with an M10 x
97mm Bolt (100), two Half Guards (72), an M10
Washer (88) and an M10 Locknut (74).
Make
sure that the Cable Trap is oriented to hold
the Low Cable in the groove of the Pulley.
100
72
71
43
5
74
69
88
72
Slack