Xerox 6180N FreeFlow® Print Server IBM® IPDS User Guide - Page 33

Mapping Stock for Use in Fusing and Non-Fusing Trays, For Non-Printing Application Data Only - printer review

Get Xerox 6180N - Phaser Color Laser Printer PDF manuals and user guides
UPC - 095205425307
View all Xerox 6180N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

IPDS User Guide Using Xerox FreeFlow® Print Server IPS Manager 1. Open the [IPS Manager] Tray Mappings tab. 2. Load the Job Profile for the job, or verify that the correct stocks are assigned to the Virtual and Physical Trays. 3. Ensure that the necessary physical stocks are loaded. If not, load the necessary stocks in the appropriate trays. 4. Review the Tray Type information in the IPS Manager Physical Tray assignment dialog, and ensure that the media selections are appropriate for the fusibility of the physical tray. 5. Review and, if necessary, update the Tray Type settings in the IPS Manager Virtual Tray mapping dialog to ensure that the host will treat the virtual trays correctly as Fuser or Inserter Trays. The physical and virtual tray dialog Tray Type columns will only be available, if there is at least one non-fusing physical tray. 6. When Virtual Trays are flagged as Inserter, the user must ensure that the media selected for the non-fusing tray, or trays, matches the attributes expected for the non-printing pages (e.g. inserts or slip sheets) generated by the application. Mapping Stock for Use in Fusing and Non-Fusing Trays If an application requires the same stock to be fed from both fuser and non-fusing trays, and the product supports this capability, configure the IPS Manager Tray Mappings, as described below. NOTE: Some products supported by Xerox FreeFlow® Print Server do not allow the same stock to be assigned to both fusing and non-fusing trays. For Non-Printing Application Data Only To feed blank or pre-printed stock without print data, from both fusing and non-fusing trays: 1. Assign the stock to the desired fuser and non-fusing physical trays in the Printer Manager 2. Assign the stock to the desired fuser and non-fusing physical trays, in the IPS Manager Tray mappings dialog 3. Assign the stock to a single virtual tray 4. Set the Tray Type for the virtual tray to Inserter. For Printing and Non-Printing Application Data To use the same stock for both printed and unprinted pages: 1. Assign the stock to the desired fuser and non-fusing physical trays in the Printer Manager. 2. Assign the stock to the desired fuser and non-fusing physical trays in the IPS Manager Tray mappings dialog. 3- 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
IPDS User Guide
3-11
Using Xerox FreeFlow® Print Server IPS Manager
1.
Open the [IPS Manager] Tray Mappings tab.
2.
Load the Job Profile for the job, or verify that the correct stocks
are assigned to the Virtual and Physical Trays.
3.
Ensure that the necessary physical stocks are loaded. If not,
load the necessary stocks in the appropriate trays.
4.
Review the Tray Type information in the IPS Manager
Physical Tray assignment dialog, and ensure that the media
selections are appropriate for the fusibility of the physical tray.
5.
Review and, if necessary, update the Tray Type settings in the
IPS Manager Virtual Tray mapping dialog to ensure that the
host will treat the virtual trays correctly as Fuser or Inserter
Trays. The physical and virtual tray dialog Tray Type columns
will only be available, if there is at least one non-fusing
physical tray.
6.
When Virtual Trays are flagged as Inserter, the user must
ensure that the media selected for the non-fusing tray, or
trays, matches the attributes expected for the non-printing
pages (e.g. inserts or slip sheets) generated by the
application.
Mapping Stock for Use in Fusing and Non-Fusing Trays
If an application requires the same stock to be fed from both fuser
and non-fusing trays, and the product supports this capability,
configure the IPS Manager Tray Mappings, as described below.
NOTE:
Some products supported by Xerox FreeFlow® Print
Server do not allow the same stock to be assigned to both fusing
and non-fusing trays.
For Non-Printing Application Data Only
To feed blank or pre-printed stock without print data, from both
fusing and non-fusing trays:
1.
Assign the stock to the desired fuser and non-fusing physical
trays in the Printer Manager
2.
Assign the stock to the desired fuser and non-fusing physical
trays, in the IPS Manager Tray mappings dialog
3.
Assign the stock to a single virtual tray
4.
Set the Tray Type for the virtual tray to Inserter.
For Printing and Non-Printing Application Data
T
o use the same stock for both printed and unprinted pages:
1.
Assign the stock to the desired fuser and non-fusing physical
trays in the Printer Manager.
2.
Assign the stock to the desired fuser and non-fusing physical
trays in the IPS Manager Tray mappings dialog.