Yamaha HTR-5280 Owner's Manual - Page 41

SPEAKER SET speaker mode, settings, 1A CENTER SP center speaker

Page 41 highlights

INTRODUCTION PREPARATION BASIC OPERATION Depending on the item, press u/d to select a sub item. 2 LOW FRQ TEST TEST TONE OFF OUTPUT MAIN L/R FRQ 88Hz 5 Press j / i repeatedly to change the setting of the item. 2 LOW FRQ TEST TEST TONE ON OUTPUT MAIN L/R FRQ 88Hz 6 Press u/d repeatedly until the current DSP program appears or simply press one of the DSP program group button to exit from the SET MENU. or Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the settings of the SET MENU you adjusted will return to the factory settings. If so, adjust the items again. SET MENU 1 SPEAKER SET (speaker mode settings) Use this feature to select suitable output modes for your speaker configuration. You must set the output mode when you use a subwoofer. Notes • When 96-kHz sampling digital signals are input to this unit, level adjustments in items 1B and 1D are possible, but those in items 1A,1C and 1E are not affected. • When 6CH INPUT is selected as the input source, level adjustments in items 1A through 1E are not affected. I 1A CENTER SP (center speaker mode) By adding a center speaker to your speaker configuration, the unit can provide good dialog localization for many listeners and superior synchronization of sound and images. The OSD shows a large, small or no center speaker depending on how you set this item. Choices: LRG (large), SML (small), NONE Initial setting: LRG LRG Select this if you have a large center speaker. The entire range of the center channel signal is directed to the center speaker. 1A CENTER SP LRG SML NONE SML Select this if you have a small center speaker. The lowfrequency signals (90 Hz and below) of the center channel are directed to the speakers selected with "1D LFE/BASS OUT". 1A CENTER SP LRG SML NONE ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78

37
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SET MENU
2 LOW FRQ TEST
TEST TONE
OFF
OUTPUT
MAIN L/R
FRQ
88Hz
Depending on the item, press
u
/
d
to select a sub
item.
5
Press
j
/
i
repeatedly to change the setting
of the item.
6
Press
u
/
d
repeatedly until the current DSP
program appears or simply press one of the
DSP program group button to exit from the
SET MENU.
2 LOW FRQ TEST
TEST TONE
ON
OUTPUT
MAIN L/R
FRQ
88Hz
1 SPEAKER SET (speaker mode
settings)
Use this feature to select suitable output modes for your
speaker configuration. You must set the output mode
when you use a subwoofer.
Notes
When 96-kHz sampling digital signals are input to this unit,
level adjustments in items 1B and 1D are possible, but those in
items 1A,1C and 1E are not affected.
When 6CH INPUT is selected as the input source, level
adjustments in items 1A through 1E are not affected.
1A CENTER SP (center speaker
mode)
By adding a center speaker to your speaker configuration,
the unit can provide good dialog localization for many
listeners and superior synchronization of sound and
images. The OSD shows a large, small or no center
speaker depending on how you set this item.
Choices: LRG (large), SML (small), NONE
Initial setting: LRG
LRG
Select this if you have a large center speaker. The entire
range of the center channel signal is directed to the center
speaker.
SML
Select this if you have a small center speaker. The low-
frequency signals (90 Hz and below) of the center channel
are directed to the speakers selected with
1D LFE/BASS
OUT
.
1A CENTER SP
LRG
SML
NONE
1A CENTER SP
LRG
SML
NONE
or
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the settings of the SET MENU you
adjusted will return to the factory settings. If so, adjust
the items again.