Yamaha HTR-5590 Owner's Manual - Page 75

INTRODUCTION PREPARATION BASIC OPERATION Changing Parameter Settings You can enjoy good quality sound with the factory-set parameters. Although you do not have to change the initial settings, you can change some of the parameters to better suit the input source or your listening room. Adjustments should be made with the remote control. y • We recommended that you edit the parameter while using a video monitor. It is easier to see the video monitor than it is to see the front panel display. 1 TRANSMIT RE-NAME CLEAR LEARN SYSTEM POWER STANDBY SLEEP 6CH INPUT A PHONO TUNER CD V-AUX CBL/SAT MD/TAPE CD-R D-TV/LD VCR 1 VCR2/DVR DVD POWER TV REC SELECT POWER AV AMP 5 REC DISC SKIP AUDIO + VOL - LEVEL TITLE TV INPUT + TV VOL SET MENU MENU A/B/C/D/E MUTE CH - TV MUTE SELECT CH + PRESET TEST RETURN HALL 1 TV VOL - CHURCH 2 PRESET ON SCREEN STEREO DISPLAY JAZZ CLUB EFFECT ROCK CONCERT 3 4 ENTERTAINMENT 5 MUSIC VIDEO 6 TV THEATER 7 MOVIE THEATER 1 8 MOVIE THEATER 2 9 /DTS SUR. 10 0 SELECT 11 +10 EX/ES 12 CHP/INDEX 4 2 3 1 Press AMP to select the AMP AMP mode. AMP appears in the display window on the remote control. 2 Turn on the video monitor and press ON SCREEN repeatedly to select the full display mode. ON SCREEN DISPLAY 3 Select a DSP program you want to adjust. HALL 1 CHURCH 2 JAZZ CLUB 3 ROCK CONCERT 4 ENTERTAINMENT 5 MUSIC VIDEO 6 TV THEATER 7 MOVIE THEATER 1 8 MOVIE THEATER 2 9 /DTS SUR. 10 0 SELECT 11 +10 EX/ES 12 CHP/INDEX SOUND FIELD PROGRAM PARAMETER EDITING 4 Press u / d to select the + parameter. TV VOL CH - PRESET TV MUTE SELECT TV VOL - CH + PRESET 5 Press j / i to change the + parameter value. TV VOL CH - PRESET TV MUTE SELECT CH + PRESET TV VOL - y • When you set the parameter to a value other than the factoryset value, an asterisk mark (*) appears by the parameter name on the video monitor. 6 Repeat steps 3 to 5 above as necessary to change other program parameters. Notes • The available parameters may be displayed on more than one OSD page for some of the programs. To scroll through pages, press u / d. • You cannot change parameter values when "14 MEMORY GUARD" on the SET MENU is set to ON. If you want to change the parameter values, set "14 MEMORY GUARD" to OFF (see page 65). Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the parameter value you edited will return to the factory setting. If so, edit the parameter value again. Resetting a Parameter to the Factory-set Value Program No. Program name Cursor P04 ROCK CONCERT ≥ DSP LEVEL............0dB INIT.DLY............15ms ROOM SIZE............1.0 LIVENESS 5 REV.TIME............1.6s REV.DELAY......120ms Parameters Parameter valves Example of the parameter setting display I To reset some of the parameters to the factory-set values Select the parameter you want to reset. Then press and hold j / i until the value temporarily stops at the factoryset value. The asterisk mark (*) by the parameter name disappears on the video monitor. I To reset all of the parameters to the factory-set values Use "9 PARAM. INI" on the SET MENU to reset all of the parameter values of all DSP programs within the selected group to the factory-set values (see page 63). This operation resets all of the parameter values of all DSP programs within that group to the factory-set values. ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 71