Yamaha MOX8 Reference Manual - Page 148

Utility Mode, F6] MIDI, SF1] OUT CH Output Channel, SF6] INFO Information, SF1] CH Channel

Get Yamaha MOX8 PDF manuals and user guides
UPC - 086792950907
View all Yamaha MOX8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 148 highlights

VOICE PERF SONG PATTERN MIX MASTER REMOTE UTILITY QUICK SET FILE DirectMonitorSw Part (Direct Monitor Switch Part) This parameter is shown only when "Mode" is set to "VST" or "2StereoRec." Determines whether or not the audio signal which is output to the external device via the "USB 3/4" channels also sounds from this instrument (Direct Monitoring). When this is set to "on," the audio signal which is output via the "USB 3/4" channels is also output to the OUTPUT [L/ MONO]/[R] jacks and [PHONES] jack. Settings: off, on [SF1] OUT CH (Output Channel) Pressing this button calls up the display which determines whether the maximum number of output channels for USB is 4 channels (2 stereo channels) or 2 channels (1 stereo channel). If transfer of the audio signal between the MOX6/MOX8 and the computer connected to the MOX6/MOX8 is compromised or impossible, set this parameter to "2ch." This setting reduces the CPU load of the computer, and may resolve the problem. After changing this setting, press the [ENTER] button, then restart the MOX6/MOX8. NOTICE After changing this setting and pressing the [ENTER] button, make sure to restart the MOX6/MOX8; the instrument will not operate otherwise. Before restarting, make sure to store any important edited data to prevent it from being inadvertently lost. Utility Mode [F1] GENERAL [F2] VOICE [F2] SEQ [F3] VCE A/D [F4] CTL ASN [F5] USB I/O [F6] MIDI Utility Job [SF6] INFO (Information) Pressing this button calls up the display which indicates the illustration of the audio connection You can confirm the "Mode" setting and "DirectMonitor Switch" setting here. [F6] MIDI [SF1] CH (Channel) From this display you can make basic MIDI settings. BasicRcvCh (Basic Receive Channel) Determines the MIDI receive channel when this synthesizer is set to single-timbre tone generator mode (Voice/ Performance modes). Settings: 1 - 16, omni (all channels), off NOTE In the multi-timbral tone generator mode (Song/Pattern modes), each Part receives MIDI data according to its assigned MIDI receive channel ([SONG] or [PATTERN]  [MIXING]  [EDIT]  Part selection  [F1] VOICE  [SF2] MODE  ReceiveCh). KBDTransCh (Keyboard Transmit Channel) Determines the MIDI channel over which the instrument sends MIDI data (to an external sequencer, tone generator, or other device). This parameter is available in the single-timbre tone generator mode (Voice/Performance modes). Settings: 1 - 16, off NOTE In the multi-timbral tone generator mode (Song/Pattern modes), MIDI data generated by playing the keyboard (and its controllers) is sent to the internal tone generator and external devices via the MIDI output channel, set from the CHANNEL display ([SONG] or [PATTERN]  [F3] TRACK  [SF1] CHANNEL). DeviceNo. (Device Number) Determines the MIDI Device Number. This number must match the Device Number of the external MIDI device when transmitting/receiving bulk data, parameter changes or other system exclusive messages. Settings: 1 - 16, all, off MOX6/MOX8 Reference Manual 148

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
PERF
SONG
PATTERN
MIX
MASTER
REMOTE
UTILITY
QUICK SET
FILE
VOICE
MOX6/MOX8 Reference Manual
Utility Mode
[F1] GENERAL
[F2] VOICE
[F2] SEQ
[F3] VCE A/D
[F4] CTL ASN
[F5] USB I/O
[F6] MIDI
Utility Job
148
DirectMonitorSw Part (Direct Monitor Switch Part)
This parameter is shown only when “Mode” is set to “VST” or “2StereoRec.” Determines whether or not the audio signal
which is output to the external device via the “USB 3/4” channels also sounds from this instrument (Direct Monitoring).
When this is set to “on,” the audio signal which is output via the “USB 3/4” channels is also output to the OUTPUT [L/
MONO]/[R] jacks and [PHONES] jack.
Settings:
off, on
[SF1] OUT CH (Output Channel)
Pressing this button calls up the display which determines whether the maximum number of output channels for USB is
4 channels (2 stereo channels) or 2 channels (1 stereo channel). If transfer of the audio signal between the MOX6/MOX8
and the computer connected to the MOX6/MOX8 is compromised or impossible, set this parameter to “2ch.” This
setting reduces the CPU load of the computer, and may resolve the problem. After changing this setting, press the
[ENTER] button, then restart the MOX6/MOX8.
NOTICE
After changing this setting and pressing the [ENTER] button, make sure to restart the MOX6/MOX8; the instrument will not
operate otherwise. Before restarting, make sure to store any important edited data to prevent it from being inadvertently lost.
[SF6] INFO (Information)
Pressing this button calls up the display which indicates the illustration of the audio connection You can confirm the
“Mode” setting and “DirectMonitor Switch” setting here.
[SF1] CH (Channel)
From this display you can make basic MIDI settings.
BasicRcvCh (Basic Receive Channel)
Determines the MIDI receive channel when this synthesizer is set to single-timbre tone generator mode (Voice/
Performance modes).
Settings:
1 – 16, omni (all channels), off
NOTE
In the multi-timbral tone generator mode (Song/Pattern modes), each Part receives MIDI data according to its assigned MIDI
receive channel ([SONG] or [PATTERN]
[MIXING]
[EDIT]
Part selection
[F1] VOICE
[SF2] MODE
ReceiveCh).
KBDTransCh (Keyboard Transmit Channel)
Determines the MIDI channel over which the instrument sends MIDI data (to an external sequencer, tone generator, or
other device). This parameter is available in the single-timbre tone generator mode (Voice/Performance modes).
Settings:
1 – 16, off
NOTE
In the multi-timbral tone generator mode (Song/Pattern modes), MIDI data generated by playing the keyboard (and its
controllers) is sent to the internal tone generator and external devices via the MIDI output channel, set from the CHANNEL
display ([SONG] or [PATTERN]
[F3] TRACK
[SF1] CHANNEL).
DeviceNo. (Device Number)
Determines the MIDI Device Number. This number must match the Device Number of the external MIDI device when
transmitting/receiving bulk data, parameter changes or other system exclusive messages.
Settings:
1 – 16, all, off
[F6] MIDI