Yamaha MOX8 Reference Manual - Page 43

VOICE PERF SONG PATTERN MIX MASTER REMOTE UTILITY QUICK SET FILE [SF4] KEY FLW (Key Follow) From this display you can set the Key Follow effect for the Filter-in other words, how the tonal qualities of the Element and its Filter EG respond to the particular notes (or octave range) you play. CutoffSens (Cutoff Key Follow Sensitivity) Determines the degree to which the notes (specifically, their position or octave range) affect the Cutoff Frequency (above) of the selected Element, assuming C3 as the basic pitch. Settings: -200% - +0% - +200% CenterKey (Cutoff Key Follow Sensitivity Center Key) This indicates that the central note for "CutoffSens" above is C3. Keep in mind that this is for display purposes only; the value cannot be changed. EGTimeSens (EG Time Key Follow Sensitivity) Determines the degree to which the notes (specifically, their position or octave range) affect the Filter EG times of the selected Element. The basic speed of change for the FEG is at the note specified in CenterKey (below). Settings: -64 - +0 - +63 CenterKey (EG Time Key Follow Sensitivity Center Key) Determines the central note for the "EGTimeSens" parameter above. Settings: C -2 - G8 NOTE You can also set the note directly from the keyboard, by holding down the [SF6] KBD button and pressing the desired key. [SF5] SCALE (Filter Scaling) Break Point 1 - 4 Determines the four Break Points by specifying the respective note numbers. Settings: C -2 - G8 NOTE You can also set the Break Point directly from the keyboard, by holding down the [SF6] KBD button and pressing the desired key. NOTE Break Point 1 to Break Point 4 will be automatically be arranged in ascending order across the keyboard. Offset 1 - 4 Determines the offset value to the Cutoff Frequency at each Break Point. Settings: -128 - +0 - +127 NOTE Regardless of the size of these Offsets, the minimum and maximum Cutoff limits (values of 0 and 127, respectively) cannot be exceeded. NOTE Any note played below the Break Point 1 note results in the Break Point 1 Level setting. Likewise, any note played above the Break Point 4 note results in the Break Point 4 Level setting. NOTE For information on setting examples for Filter Scaling, see the "Synthesizer Parameter Manual" PDF document. [F4] AMP (Amplitude) [SF1] LVL/PAN (Level/Pan) This display not only lets you make basic Level and Pan settings for each individual Element, it also gives you some detailed and unusual parameters for affecting Pan position. Level Use these to set the level of each Element. Settings: 0 - 127 Pan Determines the stereo Pan position for the selected Element. Settings: L63 (far left) - C (center) - R63 (far right) AlternatePan Determines the amount by which the sound of the selected Drum key is panned alternately left and right for each note you press. The Pan setting (above) is used as the basic Pan position. Settings: L64 - C - R63 Voice Mode Voice Play [F1] PLAY [F3] PORTA [F4] EG [F5] ARP ED [F6] EFFECT Arpeggio Edit [F2] TYPE [F3] MAIN [F4] LIMIT [F5] PLAY FX Normal Voice Edit Common Edit [F1] GENERAL [F2] OUTPUT [F3] EQ [F4] CTL SET [F5] LFO [F6] EFFECT Element Edit [F1] OSC [F2] PITCH [F3] FILTER [F4] AMP [F5] LFO [F6] EQ Drum Voice Edit Common Edit [F1] GENERAL [F2] OUTPUT [F3] EQ [F4] CTL SET [F6] EFFECT Key Edit [F1] OSC [F2] PITCH [F3] FILTER [F4] AMP [F6] EQ Voice Job [F1] INIT [F2] RECALL [F3] COPY [F4] BULK Supplementary Information MOX6/MOX8 Reference Manual 43