Yamaha MOX8 Reference Manual - Page 93

VOICE PERF SONG PATTERN MIX MASTER REMOTE UTILITY QUICK SET FILE 06: Thin Out This Job thins out the specified type of continuous data in the specified range-allowing you to free up memory space for other data or further recording. TR (Track) 001 : 1 : 000 - 999 : 4 : 479 Determines the Track (01 - 16, all) and range of measures/beats/clocks over which the Job is applied. EventType Determines the event type to be thinned. Settings: PB (Pitch Bend), CC (Control Change)*, CAT (Channel Aftertouch), PAT (Polyphonic Aftertouch), TMP (Tempo) * You can also specify the CC No. (Control Change number). NOTE The Thin Out Job will not work on continuous data that has a clock interval of greater than 60 clocks per event. 07: Modify Control Data This Job lets you change the values of a specified type of control change data (for example, pitch bend, control change, aftertouch, etc.) in the specified range. Data changes are calculated as follows: Modified value = (original value x Rate) + Offset. Any result lower than the minimum is set to the minimum; any result higher than the maximum is set to the maximum. TR (Track) 001 : 1 : 000 - 999 : 4 : 479 Determines the Track (01 - 16, TMP, all) and range of measures/beats/clocks over which the Job is applied. EventType Determines the event type to be modified. Settings: PB (Pitch Bend), CC (Control Change)*, CAT (Channel Aftertouch), PAT (Polyphonic Aftertouch), TMP (Tempo) * You can also specify the CC No. (Control Change number). SetAll Sets all target events to the same fixed value. When set to "off" the Set All parameter has no effect. When set to a value other than "off," the Rate and Offset parameters are unavailable and appear as "***" on the display. Settings: off, 000 -127 (-8192 - +0 - +8191 for pitch bend, 005.0 - 300.0 for tempo), *** Rate Determines the percentage by which the target events will be shifted from their original values. When the Set All parameter is not set to "off," this parameter appears as "***" and cannot be changed. Settings: 000% - 200%, *** Offset Adds a fixed value to the Rate-adjusted event values. When the Set All parameter is not set to "off," this parameter appears as "***" and cannot be changed. Settings: -127- +0 - +127 (-8192 - +0 - +8191 for pitch bend, -275 - +0 - +275 for tempo), *** 08: Beat Stretch This Job performs time-expansion or compression over the selected range. Keep in mind that this operation affects all event timing, note step times, and note gate times. TR (Track) 001 : 1 : 000 - 999 : 4 : 479 Determines the Track (01 - 16, all) and range of measures/beats/clocks over which the Job is applied. Rate Determines the amount of time expansion or compression as a percentage. Settings higher than 100% produce expansion, and settings below 100% produce compression. A setting of 100 produces no change. Settings: 025% - 400% Song Mode Song Play [F1] PLAY [F2] GROOVE [F3] TRACK [F6] CHAIN Song Record Song Record Standby [F1] SETUP [F2] VOICE [F3] ARP ED [F5] CLICK [F6] ALL TR During Song Recording [F1] SETUP [F3] REST [F4] TIE [F5] DELETE [F6] BAK DEL Arpeggio Edit [F1] COMMON [F2] TYPE [F3] MAIN [F4] LIMIT [F5] PLAY FX [F6] OUT CH Song Edit [F1] CHANGE [F2] VIEW FLT [F4] TR SEL [F5] INSERT [F6] DELETE Song Job [F1] UNDO/REDO [F2] NOTE [F3] EVENT [F4] MEAS [F5] TRACK [F6] SONG Supplementary Information MOX6/MOX8 Reference Manual 93