Yamaha RM1x Owner's Manual - Page 78

Rename

Page 78 highlights

PATTERN MODE 11. Disk t Rename Parameter File type Values PATT, ALL Disk file File name location File name Character RENAME! Character Delete Enter A ... ~ - - Function Specifies the file type. You can select one of two types of file to rename. For details on the types of file, refer to "Types of file used by the RM1x." (page 43) Selects the file to rename. Sets the character cursor at any location within the 8-character file name. Selects a character to be inserted at the current character location. Executes the rename operation. Moves the character cursor back one location and deletes the character at that location. Enters the character selected by Display Knob 4 (CHARACTER) at the current character location in the file name. * For information about how to change values, refer to the Basic Operation (page26). 1 Make sure the disk containing the file you want to rename is properly inserted into the RM1x floppy disk drive. 2 Use Display Knob 1 to select the type of file you want to rename: "PATT" to show only pattern files in the file list, or "ALL" to show all available files in the file list. n • If the filename extension of an SMF file is renamed, it may become impossible to load the file. • The disk write-protect slide must be in the write-enable position to perform a rename operation. If it is not, the "Write Protected!" error message will appear when you attempt to execute the rename operation. 3 Use Display Knob 2 to select the file you want to rename from the file list on the display. 4 Enter a new file name. Use Display Knobs 3 and 4 to select a character location and character, then press the F4 function button (Enter) to enter the specified character at the selected location. Repeat until the file name is complete. 5 Press the F1 function button (RENAME!). "Executing" will appear while the file is being renamed. 78 RM1x SEQUENCE REMIXER

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154

78
RM1x SEQUENCE REMIXER
PATTERN MODE
Rename
1
Make sure the disk containing the file you want to
rename is properly inserted into the RM1x floppy disk
drive.
2
Use Display Knob 1 to select the type of file you want
to rename: “PATT” to show only pattern files in the file
list, or “ALL” to show all available files in the file list.
3
Use Display Knob 2 to select the file you want to re-
name from the file list on the display.
4
Enter a new file name. Use Display Knobs 3 and 4 to
select a character location and character, then press
the F4 function button (Enter) to enter the specified
character at the selected location. Repeat until the
file name is complete.
5
Press the F1 function button (RENAME!). “Execut-
ing” will appear while the file is being renamed.
11. Disk
Parameter
Values
Function
File type
PATT, ALL
Specifies the file type.
You can select one of two types of file to rename. For details on the
types of file, refer to “Types of file used by the RM1x.” (page 43)
Disk file
Selects the file to rename.
File name location
Sets the character cursor at any location within the 8-character file
name.
File name Character
A ... ~
Selects a character to be inserted at the current character location.
RENAME!
-
Executes the rename operation.
Character Delete
-
Moves the character cursor back one location and deletes the char-
acter at that location.
Enter
-
Enters the character selected by Display Knob 4 (CHARACTER) at
the current character location in the file name.
n
If the filename extension of an SMF file is renamed, it
may become impossible to load the file.
The disk write-protect slide
must be in the write-enable
position to perform a rename operation. If it is not, the
“Write Protected!” error message will appear when you
attempt to execute the rename operation.
*
For information about how to change values, refer to the Basic Operation (page26).