Yamaha SY85 Owner's Manual (getting Started) (image) - Page 37

Select the Performance Edit LAYER Mode, Select the Voices for Each Layer

Get Yamaha SY85 PDF manuals and user guides View all Yamaha SY85 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Respond to "Are you sure?" on the display by pressing the [ENTER/YES] key again. "Completed" will appear for a few seconds when the initialization job has finished. PERFORMANCE`JOB`Initialize Completed EDIT]`LYR````` 3. Select the Performance Edit "LAYER" Mode k l Press the SUB MODE [EDIT] key. This selects the performance edit mode. Use the PAGE [ ] and [ ] keys to select the "LAYER" entry screen (if it doesn't appear immediately). LAYER Hit`[ENTER] When you've located this screen, press [ENTER/YES] to engage the performance edit LAYER mode. 4. Select the Voices for Each Layer k If the "LAYER Voice Number" display doesn't appear as soon as you engage the performance edit mode, press the PAGE [ ] key a few times until it does appear (see the "HINT", below). LAYER`Voice`Number````````ABCD ````A=¡A1`````B=¡A1`````C=¡A1`````D=¡A1` The voice numbers assigned to each layer are shown across the bottom of the display. After initialization, voice "IIA1" is assigned to all four layers. Press the [F2] function key to place the underline cursor under the layer-A voice number (note that the voice name is shown between parentheses in the upper right corner of the display), then use the [CS2] control slider or any of the voice selection methods already described to select voice number "IIC1" (BA Wood). Next press the [F4] function key to select the layer-B voice number, and use the [CS4] control slider or any other voice selection method to select voice number "IIB1" (AP Grand). Next press the [F6] function key to select the layer-C voice number, and use the [CS6] control slider or any other voice selection method to select voice number "IID1" (ST Power). Finally, press the [F8] function key to select the layer-D voice number and, while holding the [SHIFT] key, press the [-1] key to turn layer-D "off". 3. The Performance Mode 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
3. The Performance Mode
35
Respond to “Are you sure?” on the display by pressing the [ENTER/YES]
key again. “Completed” will appear for a few seconds when the initialization
job has finished.
3.
Select the Performance Edit “LAYER” Mode
Press the SUB MODE [EDIT] key. This selects the performance edit mode.
Use the PAGE [
] and [
] keys to select the “LAYER” entry screen (if it
doesn’t appear immediately).
When you’ve located this screen, press [ENTER/YES] to engage the per-
formance edit LAYER mode.
4.
Select the Voices for Each Layer
If the “LAYER Voice Number” display doesn’t appear as soon as you
engage the performance edit mode, press the PAGE [
] key a few times until
it does appear (see the “HINT”, below).
The voice numbers assigned to each layer are shown across the bottom of
the display. After initialization, voice “
I
I
A1” is assigned to all four layers.
Press the [F2] function key to place the underline cursor under the layer-A
voice number (note that the voice name is shown between parentheses in the
upper right corner of the display), then use the [CS2] control slider or any of
the voice selection methods already described to select voice number “
I
I
C1”
(BA Wood).
Next press the [F4] function key to select the layer-B voice number, and
use the [CS4] control slider or any other voice selection method to select voice
number “
I
I
B1” (AP Grand).
Next press the [F6] function key to select the layer-C voice number, and
use the [CS6] control slider or any other voice selection method to select voice
number “
I
I
D1” (ST Power).
Finally, press the [F8] function key to select the layer-D voice number and,
while holding the [SHIFT] key, press the [-1] key to turn layer-D “off”.