Yamaha YSP-5100BL Owners Manual - Page 13

Connecting a subwoofer, Connecting audio and video components

Get Yamaha YSP-5100BL PDF manuals and user guides View all Yamaha YSP-5100BL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

INTRODUCTION PREPARATION PLAYBACK FEATURES ■ Connecting audio and video components Determine the connection types depending on the jacks available on this unit and your external components. The symbols in the following table correspond with the symbols described in "Cables used for connections" (page 12). HDMI IN 1 IN 2 IN 3 IN 4 IN OUT AUX 1 TV AUX 2 AUX 1 TV VIDEO AUDIO IN DIGITAL IN IR IN RS-232C VIDEO AUDIO IN DIGITAL IN VIDEO IN/OUT AUDIO IN DIGITAL IN jacks jacks jacks HDMI IN jacks External component Signal type TV Video Jacks to use On external component On this unit Composite video input VIDEO OUT Cable to use Input selection key Audio Analog audio output AUDIO IN (TV) TV External component with HDMI output External component with component video output Audio/video Audio Video HDMI output Coaxial digital output Component video output HDMI IN 1-4 DIGITAL IN (AUX 2) VIDEO IN (COMPONENT) HDMI1-4 AUX2 External component with composite video output Audio Optical digital output Analog audio output DIGITAL IN (AUX 1) AUDIO IN (AUX 1) AUX1 Video Composite video output VIDEO IN (VIDEO) y • Video signals input from the VIDEO IN (VIDEO) jack can be output not only to the VIDEO OUT jack but also the HDMI OUT jack. Video signals input from the VIDEO IN (COMPONENT) jacks are output to the HDMI OUT jack. Connecting a subwoofer Wireline connection Connect the monaural input jack on your subwoofer to the SUBWOOFER jack on this unit. SUB WOOFER SIRIUS SYSTEM CONNECTOR Wireless connection You can make a wireless connection of your subwoofer by using the Yamaha wireless subwoofer kit (SWK-W10). About SWK-W10, refer to "Safety and Accessory Information" (separate booklet). See also: "WIRELESS SETUP" (page 39) OUT AUX 1 TV AUX 2 AUDIO IN AUX 1 TV DIGITAL IN IR IN RS-232C Monaural input System connector y • If the subwoofer is connected by using a system type connection, changing the power mode of this unit controls the power mode of the subwoofer (Yamaha subwoofer). INPUT VOLUME INTELLIBEAM MIC SWK-W10 Subwoofer y • For proper transmission, you need to set the group IDs of this unit and SWK-W10 to the same value. For the Group ID settings, refer to "Group ID" (page 39) and "Safety and Accessory Information (separate booklet)". Note • Be sure to use the product only in the country in where it was purchased. SETTINGS APPENDIX 13 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
13
En
PREPARATION
INTRODUCTION
APPENDIX
PLAYBACK FEATURES
SETTINGS
■
Connecting audio and video components
Determine the connection types depending on the jacks available on this unit and your external components. The symbols in the following table
correspond with the symbols described in “Cables used for connections” (page 12).
y
•
Video signals input from the VIDEO IN (VIDEO) jack can be output not only to the VIDEO OUT jack but also the HDMI OUT jack. Video signals input from
the VIDEO IN (COMPONENT) jacks are output to the HDMI OUT jack.
Wireline connection
Connect the monaural input jack on your subwoofer to the
SUBWOOFER jack on this unit.
y
•
If the subwoofer is connected by using a system type connection, changing
the power mode of this unit controls the power mode of the subwoofer
(Yamaha subwoofer).
Wireless connection
You can make a wireless connection of your subwoofer by using the
Yamaha wireless subwoofer kit (SWK-W10). About SWK-W10,
refer to “Safety and Accessory Information” (separate booklet).
See also: “WIRELESS SETUP” (page 39)
y
•
For proper transmission, you need to set the group IDs of this unit and
SWK-W10 to the same value. For the Group ID settings, refer to “Group
ID” (page 39) and “Safety and Accessory Information (separate booklet)”.
Note
•
Be sure to use the product only in the country in where it was purchased.
External component
Signal type
Jacks to use
Cable to
use
Input selection
key
On external component
On this unit
TV
Video
Composite video input
VIDEO OUT
Audio
Analog audio output
AUDIO IN (TV)
TV
External component
with HDMI output
Audio/video
HDMI output
HDMI IN 1-4
HDMI1-4
External component
with component video
output
Audio
Coaxial digital output
DIGITAL IN (AUX 2)
AUX2
Video
Component video output
VIDEO IN (COMPONENT)
External component
with composite video
output
Audio
Optical digital output
DIGITAL IN (AUX 1)
AUX1
Analog audio output
AUDIO IN (AUX 1)
Video
Composite video output
VIDEO IN (VIDEO)
Connecting a subwoofer
HDMI
IN 1
IN 2
IN 3
IN 4
A
UX 1
TV
A
UX 2
A
UX 1
TV
OUT
IN
IR IN
DIGIT
T
T
A
UDIO IN
VIDEO
RS-232C
DIGITAL IN
AUDIO IN
VIDEO
VIDEO IN/OUT
jacks
AUDIO IN
jacks
DIGITAL IN
jacks
HDMI IN
jacks
AUX 1
TV
AUX 2
AUX 1
TV
OUT
IR IN
SYSTEM
CONNECTOR
SIRIUS
SUB
WOOFER
DIGITAL IN
AUDIO IN
RS-232C
Monaural input
System connector
SWK-W10
Subwoofer