Yamaha YSP-5100BL Owners Manual - Page 38

TV AV TV AUX 1 AUX 2 HDMI 1 HDMI 2 HDMI 3 HDMI 4 iPod RADIO MOVIE ENTER MUSIC TAINMENT OFF CINEMA DSP SURROUND STEREO ENTER TOP MENU OPTION SETUP MENU RETURN TV VOL CH VOLUME G I TV MUTE TV INPUT MUTE UNIVOLUME SUR. DECODE INTELLIBEAM 1 2 3 4 5 6 7 8 9 0 +10 ENT CODE SET TUNING PRESET CATEGORY INFO MEMORY SLEEP GENTER G / G / G IRETURN SOUND OUT (Sound output redirection) Use to redirect the output of audio signals. Audio output of all the channels switches simultaneously. Choices: SPEAKER*, PRE OUT • Select SPEAKER to output sounds from this unit. • Select PRE OUT to output audio signals from the PRE OUT jacks of this unit. You also need to configure the parameters from "BASS OUT" to "LFE Level" described below. y • The parameters from "BASS OUT" to "LFE Level" are settings for the PRE OUT jacks when they are selected as audio output jacks. BASS OUT (Bass sound output redirection) Use to redirect the output of bass sounds. The settings under "BASS OUT" are for the PRE OUT jacks. Choices: SUBWOOFER, FRONT* • Select SUBWOOFER to output bass sounds from the subwoofer. • Select FRONT to output bass sounds from the external front right and left speakers. Front SP Size (Front speaker size for PRE OUT) Select the size of external front speakers. Choices: Small, Large* • Select Small if the diameter of the front speaker's woofer is smaller than 16 cm. Low-frequency parts of front right and left channel signals are output from the subwoofer. Center SP Size (Center speaker size for PRE OUT) Select the size of external center speakers. Choices: None, Small* • Select None if no center speaker is used. Center channel signals are mixed into the front right and left speakers. • Select Small if a center speaker is used. Low-frequency parts of center channel signals are output from the subwoofer (or mixed into the front right and left channel signals if subwoofer is not available). PRE OUT Volume (PRE OUT volume) Adjust the output level of the PRE OUT jacks. Control range: -30.0 dB to 0.0 dB Initial setting: -18.0 dB LFE Level (Low-frequency effect level for PRE OUT) Adjust the low-frequency effect output level of the PRE OUT jacks. This setting is effective only when this unit decodes Dolby Digital or DTS signals. Control range: -20 dB to + 0 dB* INPUT MENU ■ INPUT ASSIGNMENT (Input assignment) SET MENU → INPUT MENU → INPUT ASSIGNMENT Use to change the key assignments of input jacks on this unit. The parenthetic references displayed in the menu screen indicate the initial settings. See also: "AUDIO SELECT" (page 39) y • Press G to proceed to the next page. AUDIO1 Select the key to which the AUDIO IN (TV) jacks are assigned. Choices: TV*, AUX1, AUX2, HDMI1, HDMI2, HDMI3, HDMI4 Note • The input already selected in "AUDIO2" is not displayed. To set the input selected in "AUDIO2", change "AUDIO2" parameter, and then reconfigure. AUDIO2 Select the key to which the AUDIO IN (AUX 1) jacks are assigned. Choices: AUX1*, AUX2, HDMI1, HDMI2, HDMI3, HDMI4, TV Note • The input already selected in "AUDIO1" is not displayed. To set the input selected in "AUDIO1", change "AUDIO1" parameter, and then reconfigure. OPTICAL1 Select the key to which the DIGITAL IN (TV) jack is assigned. Choices: TV*, AUX1, AUX2, HDMI1, HDMI2, HDMI3, HDMI4 Note • The input already selected in "OPTICAL2" or "COAX" is not displayed. To set the input selected in one of these parameters, change the corresponding parameter, and then reconfigure. OPTICAL2 Select the key to which the DIGITAL IN (AUX 1) jack is assigned. Choices: AUX1*, AUX2, HDMI1, HDMI2, HDMI3, HDMI4, TV Note • The input already selected in "OPTICAL1" or "COAX" is not displayed. To set the input selected in one of these parameters, change the corresponding parameter, and then reconfigure. COAX Select the key to which the DIGITAL IN (AUX 2) jack is assigned. Choices: AUX2*, HDMI1, HDMI2, HDMI3, HDMI4, TV, AUX1 Note • The input already selected in "OPTICAL1" or "OPTICAL2" is not displayed. To set the input selected in one of these parameters, change the corresponding parameter, and then reconfigure. ■ INPUT RENAME (Input rename) SET MENU → INPUT MENU → INPUT RENAME Use to change the name of the input source displayed when the input source is selected. Select a name from templates, or enter an original name. Selecting a name from templates 1 Press G / be renamed. to select the input source to 38 En