Yamaha YSP 900 Owner's Manual - Page 34

SET MENU, AUTO SETUP, Press MENU on the remote control. - test

Get Yamaha YSP 900 - Digital Sound Projector Five CH Speaker PDF manuals and user guides
UPC - 027108928302
View all Yamaha YSP 900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

AUTO SETUP (IntelliBeam) p p p p Notes • Make sure that your listening room is as quiet as possible while this unit is performing the AUTO SETUP procedure. • To achieve the best results possible, evacuate yourself from your listening room until the AUTO SETUP procedure is completed so that you may not obstruct the path of sound beams. • Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure. • The AUTO SETUP procedure may not be run successfully if this unit is installed in one of the rooms described in "Before installing this unit" on page 11. In such cases, run MANUAL SETUP (see page 57) to manually adjust the corresponding parameters. • If an error occurs, an error buzzer is played, the AUTO SETUP procedure stops and then an error message appears on the screen. See "Error messages for AUTO SETUP" on page 33 for appropriate remedies. y • The AUTO SETUP procedure takes about 3 minutes maximum. A chime is played when the AUTO SETUP procedure is run successfully. • If there are curtains in your listening room, we recommend following the procedure below. 1. Open the curtains to improve sound reflection. 2. Run BEAM OPTIMZ only. 3. Close the curtains. 4. Run SOUND OPTIMZ only. • You can save the settings optimized by the AUTO SETUP procedure (see page 34). A set of settings optimized according to specific conditions of your listening environment can be recalled later depending on the varying conditions of your listening environment (see page 35). 1 Press STANDBY/ON on the front panel or on the remote control to turn on the power of this unit. If a subwoofer is connected to this unit, turn on the power of the subwoofer. 3 Press MENU on the remote control. The SET MENU screen appears on your TV. MENU SET MENU . ;MEMORY ;AUTO SETUP ;MANUAL SETUP ;LANGUAGE SETUP [ ]/[ ]:Up/Down [ENTER]:Enter y • The control buttons used for SET MENU are displayed on the bottom of the screen. • To return to the previous screen while using SET MENU, press RETURN on the remote control. • To cancel the SET MENU screen, press MENU again. • You can start the BEAM+SOUND OPTIMZ procedure simply by pressing and holding AUTO SETUP on the remote control for more than 2 seconds. Step 4 and 5 are skipped and then the screen shown in step 5 is displayed on your TV. Start the AUTO SETUP procedure from step 6. • You can also perform the following operations in the front panel display. 4 Press / on the remote control to select AUTO SETUP and then press ENTER. The following screen appears on your TV. ENTER ENTER STANDBY/ON Front panel or Remote control 2 Set the operation mode selector to YSP to switch to the operation mode of this unit. ;AUTO SETUP . 1)BEAM+SOUND OPTIMZ 2)BEAM OPTIMZ only 3)SOUND OPTIMZ only [ ]/[ ]:Up/Down [ENTER]:Enter TV/AV YSP 30 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
AUTO SETUP (IntelliBeam)
30
En
•
Make sure that your listening room is as quiet as possible while
this unit is performing the AUTO SETUP procedure.
•
To achieve the best results possible, evacuate yourself from
your listening room until the AUTO SETUP procedure is
completed so that you may not obstruct the path of sound
beams.
•
Be advised that it is normal for loud test tones to be output
during the AUTO SETUP procedure.
•
The AUTO SETUP procedure may not be run successfully if
this unit is installed in one of the rooms described in “Before
installing this unit” on page 11. In such cases, run MANUAL
SETUP (see page 57) to manually adjust the corresponding
parameters.
•
If an error occurs, an error buzzer is played, the AUTO SETUP
procedure stops and then an error message appears on the
screen. See “Error messages for AUTO SETUP” on page 33 for
appropriate remedies.
y
•
The AUTO SETUP procedure takes about 3 minutes maximum.
A chime is played when the AUTO SETUP procedure is run
successfully.
•
If there are curtains in your listening room, we recommend
following the procedure below.
1. Open the curtains to improve sound reflection.
2. Run BEAM OPTIMZ only.
3. Close the curtains.
4. Run SOUND OPTIMZ only.
•
You can save the settings optimized by the AUTO SETUP
procedure (see page 34). A set of settings optimized according
to specific conditions of your listening environment can be
recalled later depending on the varying conditions of your
listening environment (see page 35).
1
Press STANDBY/ON on the front panel or on
the remote control to turn on the power of
this unit.
If a subwoofer is connected to this unit, turn on the
power of the subwoofer.
2
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
3
Press MENU on the remote control.
The SET MENU screen appears on your TV.
y
•
The control buttons used for SET MENU are displayed on
the bottom of the screen.
•
To return to the previous screen while using SET MENU,
press RETURN on the remote control.
•
To cancel the SET MENU screen, press MENU again.
•
You can start the BEAM+SOUND OPTIMZ procedure
simply by pressing and holding AUTO SETUP on the
remote control for more than 2 seconds. Step 4 and 5 are
skipped and then the screen shown in step 5 is displayed
on your TV. Start the AUTO SETUP procedure from
step 6.
•
You can also perform the following operations in the front
panel display.
4
Press
/
on the remote control to select
AUTO SETUP and then press ENTER.
The following screen appears on your TV.
Notes
STANDBY/ON
or
Front panel
Remote control
YSP
TV/AV
MENU
;
MEMORY
;
AUTO SETUP
;
MANUAL SETUP
;
LANGUAGE SETUP
[ ]/[ ]:Up/Down
[ENTER]:Enter
SET MENU
.
p
p
ENTER
ENTER
1)BEAM+SOUND OPTIMZ
2)BEAM OPTIMZ only
3)SOUND OPTIMZ only
[ ]/[ ]:Up/Down
[ENTER]:Enter
;
AUTO SETUP
.
p
p