Zenith H20H52DT Operating Guide - Page 40

Before you begin, WARNING, A. Set Up a Master TV, B. Connect Clone to Master TV

Get Zenith H20H52DT PDF manuals and user guides View all Zenith H20H52DT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

LT2000 QuickSet Programmer Before you begin: • The "master TV" should be connected to a good, stable signal from an over-the-air antenna or cable service and turned on. • Teaching and Learning is only possible between identical model Zenith TVs. (However, the Clone programmer can store 4 different master TV setups.) WARNING: Copying a blank or incorrect memory into a TV will cause the TV to operate erratically or become inoperable. • Use a Zenith MBR Remote like the MBR3447 or the TV front panel controls to operateM Learning and Teaching menus. • Make sure that the batteries in the Clone programmer are fresh. • If the batteries are removed, the Clone Clock time will be lost. • Decide if you want to set the time from the Clone programmer or copy the time to the Clone programmer; from a TV which has the clock set to the current time. • Follow the connection diagrams above to connect the Clone to a master TV and, after learning is complete, to another TV to "teach" it the setup. • Setting the time and transferring it to the Clone or another TV is a separate procedure. • Once a TV's setup is copied to another TV, that TV needs to be disconnected from power for about 5 seconds to activate the newly copied setup. • See Troubleshooting to solve problems. A. Set Up a Master TV Using a Zenith Multi-Brand remote like the MBR3447, set up a "Master" TV with custom settings and features as described in the master Tv's operating guide. The master TV's Setup is what you will copy to the Clone Programmer and transfer to TVs of the same model so they will operate identically. B. Connect Clone to Master TV If there is a good connection, the "Clone has Control of TV" message will appear. (See menu above.) A slow flashing green light indicates there is a problem with the communications between the TV and the programmer. In this case, check for a damaged cable, poor contacts, or other connection troubles. If the status indicator is red, the programmer batteries are low and should be replaced. Use 4 good-quality alkaline AA batteries. Page 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Page 40
LT2000 QuickSet Programmer
Before you begin:
• The “master TV” should be connected to a
good, stable signal from an over-the-air
antenna or cable service and turned on.
• Teaching and Learning is only possible
between identical model Zenith TVs.
(However, the Clone programmer can store 4
different master TV setups.)
WARNING:
Copying a blank or
incorrect memory into a TV will cause
the TV to operate erratically or
become inoperable.
• Use a Zenith MBR Remote like the
MBR3447 or the TV front panel controls to
operateM Learning and Teaching menus.
• Make sure that the batteries in the Clone
programmer are fresh.
• If the batteries are removed, the Clone Clock
time will be lost.
• Decide if you want to set the time from the
Clone programmer or copy the time to the
Clone programmer; from a TV which has the
clock set to the current time.
• Follow the connection diagrams above to
connect the Clone to a master TV and, after
learning is complete, to another TV to “teach”
it the setup.
• Setting the time and transferring it to
the Clone or another TV is a separate
procedure.
• Once a TV’s setup is copied to another
TV, that TV needs to be disconnected
from power for about 5 seconds to
activate the newly copied setup.
• See Troubleshooting to solve problems.
A. Set Up a Master TV
Using a Zenith Multi-Brand remote like
the MBR3447, set up a “Master” TV with
custom settings and features as
described in the master Tv’s
operating
guide. The master TV’s Setup is what
you will copy to the Clone Programmer
and transfer to TVs of the same model
so they will operate identically.
B. Connect Clone to Master TV
If there is a good connection, the “Clone
has Control of TV” message
will appear.
(See menu above.)
A slow flashing green light indicates there is a problem with the communications
between the TV and the programmer. In this case, check for a damaged cable, poor
contacts, or other connection troubles.
If the status indicator is red, the programmer batteries are low and should be replaced.
Use 4 good-quality alkaline AA batteries.