Zenith H20H52DT Operating Guide - Page 7

Cable Service CATV Hook Up - pillow speaker

Get Zenith H20H52DT PDF manuals and user guides View all Zenith H20H52DT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Cable Service (CATV) Hook Up Connect cable service to the HealthView TV. Locate the Antenna/Cable jack on the 1 back of the HealthView TV. Connect the cable service wire that runs 2 from the wall, according to one of the diagrams to the right. Remove the back of the optional remote 3 and put in two AA batteries. Cable TV Wall Jack TV Back Back of Remote RF Coaxial Wire (75 ohm) 4 Plug in the TV. The HealthView TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power. 5 Go to page 11 to Auto Program the TV. Cable TV Wall Jack In Cable Box Out output switch 3 4 If you're using a cable box, leave the TV on channel 3 or 4 and use the cable box to change channels. If you're using a cable box, Auto Program might only find the channel the cable service is on (usually channel 3 or 4). RF Coaxial Wire (75 ohm) ANTENNA CABLE TV SPEAKER M.P.I. PILLOW SPEAKER VIDEO IN SPEAKER OUT AUDIO IN TV Back Panel (Expanded View) TV Back ANTENNA CABLE TV SPEAKER M.P.I. PILLOW SPEAKER VIDEO IN SPEAKER OUT AUDIO IN TV Back Panel (Expanded View) Page 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Cable Service (CATV) Hook Up
Connect cable service to the HealthView TV.
Cable TV
Wall Jack
RF Coaxial Wire
(75ohm)
TV Back
ANTENNA
CABLE
M.P.I.
TV Back Panel
(Expanded View)
PILLOW SPEAKER
TV SPEAKER
VIDEO IN
SPEAKER OUT
AUDIO IN
ANTENNA
CABLE
M.P.I.
TV Back Panel
(Expanded View)
PILLOW SPEAKER
TV SPEAKER
VIDEO IN
SPEAKER OUT
AUDIO IN
Cable TV
Wall Jack
Cable Box
In
Out
RF Coaxial Wire
(75ohm)
3 4
output
switch
TV Back
Back of
Remote
1
2
3
4
5
Page 7
Locate the Antenna/Cable jack on the
back of the HealthView TV.
Connect the cable service wire that runs
from the wall, according to one of the
diagrams to the right.
Remove the back of the optional remote
and put in two AA batteries.
Plug in the TV. The HealthView TV is
designed to operate on standard current,
120-volt 60 Hertz AC. Do not attempt to
operate it on DC power.
Go to page 11 to Auto Program the TV.
If you’re using a cable box, leave the TV on
channel 3 or 4 and use the cable box to
change channels.
If you’re using a cable box, Auto Program
might only find the channel the cable
service is on (usually channel 3 or 4).