Home » ZyXEL Manuals » Wireless » ZyXEL LTE7485-S905 » Manual Viewer

ZyXEL LTE7485-S905 User Guide - Page 154

Cellular WAN Status, LTE Series User's Guide, Table 63

Add to My Manuals
Save this manual to your list of manuals

Page 154 highlights

Chapter 18 Cellular WAN Status Table 63 System Monitor > Cellular WAN Status (continued) LABEL DESCRIPTION IP Passthrough Enable IP Passthrough Mode This displays if IP Passthrough is enabled on the Zyxel Device. IP Passthrough allows a LAN computer on the local network of the Zyxel Device to have access to web services using the public IP address. When IP Passthrough is configured, all traffic is forwarded to the LAN computer and will not go through NAT. This displays the IP Passthrough mode. This displays Dynamic and the Zyxel Device will allow traffic to be forwarded to the first LAN computer requesting an IP address from the Zyxel Device. Cellular Status Data Roaming This displays Fixed and the Zyxel Device will allow traffic to be forwarded to a specific LAN computer on the local network of the Zyxel Device. This displays the status of the cellular Internet connection. This displays if data roaming is enabled on the Zyxel Device. Operator PLMN Access Technology Band RSSI 4G roaming is to use your Zyxel Device in an area which is not covered by your service provider. Enable roaming to ensure that your Zyxel Device is kept connected to the Internet when you are traveling outside the geographical coverage area of the network to which you are registered. This displays the name of the service provider. This displays the PLMN number. This displays the type of the mobile network (such as LTE, UMTS, GSM) to which the Zyxel Device is connecting. This displays the current LTE band of your Zyxel Device (WCDMA2100). This displays the strength of the WiFi signal between an associated wireless station and an AP. Cell ID The normal range is -30dBm to -79dBm. If the value drops below -80dBm, try moving the associated wireless station closer to the Zyxel Device to get better signal strength. This shows the cell ID, which is a unique number used to identify the Base Transceiver Station to which the Zyxel Device is connecting. The value depends on the Current Access Technology: Physical Cell ID UL Bandwidth (MHz) DL Bandwidth (MHz) RFCN • For GPRS, it is the Cell Identity as specified in 3GPP-TS.25.331. • For UMTS, it is the Cell Identity as defined in SIB3 3GPP-TS.25.331, 3GPP-TS.24.008. • For LTE, it is the 28-bit binary number Cell Identity as specified in SIB1 in 3GPP-TS.36.331. The value is '0' (zero) or 'N/A' if there is no network connection. This shows the Physical Cell ID (PCI), which are queries and replies between the Zyxel Device and the mobile network it is connecting to. The normal range is 1 to 504. This shows the LTE channel bandwidth from device to base station. According to 3GPP specifications, the bandwidths defined by the standard are 1.4, 3, 5, 10, 15, and 20 MHz. The wider the bandwidth the higher the throughput. This shows the LTE channel bandwidth from base station to LTE device. According to 3GPP specifications, the bandwidths defined by the standard are 1.4, 3, 5, 10, 15, and 20 MHz. The wider the bandwidth the higher the throughput. This displays the Radio Frequency Channel Number of DL carrier frequency used by the mobile network to which the Zyxel Device is connecting. The value depends on the Current Access Technology: • For GPRS, it is the ARFCN (Absolute Radio-Frequency Channel Number) as specified in 3GPPTS.45.005. • For UMTS, it is the UARFCN (UTRA Absolute Radio-Frequency Channel Number) as specified in 3GPP-TS.25.101. • For LTE, it is the EARFCN (E-UTRA Absolute Radio-Frequency Channel Number) as specified in 3GPP-TS.36.101. The value is '0' (zero) or 'N/A' if there is no network connection. LTE Series User's Guide 154

Section	Page
LTE Series	1
Document Conventions	3
Contents Overview	4
Table of Contents	5
User’s Guide	12
Introduction	13
1.1 Overview	13
1.2 Application for the Zyxel Device	14
1.3 Manage the Zyxel Device	14
1.4 Good Habits for Managing the Zyxel Device	15
1.5 Front and Bottom Panels	15
1.5.1 LEDs (Lights)	17
1.5.2 Panel Ports & Buttons	17
1.5.3 Turning On/Off WiFi	18
1.5.4 The RESET Button	19
The Web Configurator	21
2.1 Overview	21
2.1.1 Access the Web Configurator	21
2.2 Web Configurator Layout	23
2.2.1 Settings Icon	23
2.2.2 Widget Icon	27
Quick Start	30
3.1 Overview	30
3.2 Quick Start Setup	30
3.3 Time Zone	30
3.4 The Internet Connection Setup	31
3.4.1 Successful Internet Connection	31
3.4.2 Unsuccessful Internet Connection	32
3.5 Quick Start Setup-Wireless	32
3.6 Quick Start Setup-Finish	33
Tutorials	34
4.1 Overview	34
4.2 Set Up a Wireless Network Using WPS	34
4.2.1 Push Button Configuration (PBC)	35
4.2.2 PIN Configuration	36
4.3 Connect to the Zyxel Device’s WiFi Network	37
4.4 Configure a Firewall Rule	40
4.5 Configure MAC Filter	41
4.6 Upgrade Firmware on the Zyxel Device	42
4.7 Back up a Configuration File	43
4.8 Restore Configuration	43
4.9 Configure DHCP	44
4.9.1 Add Devices to Your Static DHCP List	45
4.10 Configure Static Route for Routing to Another Network	46
4.11 Access the Zyxel Device Using DDNS	48
4.11.1 Register a DDNS Account on www.dyndns.org	49
4.11.2 Configure DDNS on Your Zyxel Device	49
4.11.3 Test the DDNS Settings	50
Technical Reference	51
Connection Status	52
5.1 Connection Status Overview	52
5.1.1 Connectivity	52
5.1.2 System Info	53
5.1.3 Cellular Info	55
5.1.4 WiFi Settings	59
5.1.5 LAN	60
Broadband	63
6.1 Overview	63
6.1.1 What You Can Do in this Chapter	63
6.1.2 What You Need to Know	64
6.1.3 Before You Begin	64
6.2 Broadband	64
6.3 Cellular WAN	65
6.4 Cellular APN	66
6.5 Cellular SIM Configuration	67
6.6 Cellular Band Configuration	68
6.7 Cellular PLMN Configuration	69
6.8 Cellular IP Passthrough	72
6.9 Cellular Lock	73
Home Networking	75
7.1 Overview	75
7.1.1 What You Can Do in this Chapter	75
7.1.2 What You Need To Know	75
7.2 LAN Setup	76
7.3 Static DHCP	80
7.3.1 Before You Begin	80
7.4 UPnP	82
7.5 Technical Reference	83
7.6 Turn on UPnP in Windows 7 Example	84
7.6.1 Auto-discover Your UPnP-enabled Network Device	85
7.7 Turn on UPnP in Windows 10 Example	87
7.7.1 Auto-discover Your UPnP-enabled Network Device	89
7.8 Web Configurator Easy Access in Windows 7	92
7.9 Web Configurator Easy Access in Windows 10	94
Routing	97
8.1 Overview	97
8.2 Configure Static Route	97
8.2.1 Add/Edit Static Route	98
8.3 DNS Route	100
8.3.1 Add/Edit DNS Route	100
8.4 Policy Route	101
8.4.1 Add/Edit Policy Route	103
8.5 RIP Overview	104
8.5.1 RIP	104
Network Address Translation (NAT)	105
9.1 Overview	105
9.1.1 What You Can Do in this Chapter	105
9.1.2 What You Need To Know	105
9.2 Port Forwarding Overview	106
9.2.1 Port Forwarding	107
9.2.2 Add/Edit Port Forwarding	107
9.3 Port Triggering	109
9.3.1 Add/Edit Port Triggering Rule	111
9.4 DMZ	112
9.5 ALG	113
Dynamic DNS Setup	115
10.1 DNS Overview	115
10.1.1 What You Can Do in this Chapter	115
10.1.2 What You Need To Know	115
10.2 DNS Entry	116
10.2.1 Add/Edit DNS Entry	116
10.3 Dynamic DNS	117
Firewall	119
11.1 Overview	119
11.1.1 What You Need to Know About Firewall	119
11.2 Firewall	120
11.2.1 What You Can Do in this Chapter	120
11.3 Firewall General Settings	120
11.4 Protocol (Customized Services)	122
11.4.1 Add Customized Service	122
11.5 Access Control (Rules)	123
11.5.1 Add New ACL Rule Screen	124
11.6 DoS	126
11.7 Firewall Technical Reference	127
11.7.1 Firewall Rules Overview	127
11.7.2 Guidelines For Security Enhancement With Your Firewall	128
11.7.3 Security Considerations	128
MAC Filter	130
12.1 MAC Filter Overview	130
12.2 MAC Filter	130
12.2.1 Add New Rule	131
Certificates	132
13.1 Certificates Overview	132
13.1.1 What You Can Do in this Chapter	132
13.2 Local Certificates	132
13.2.1 Create Certificate Request	133
13.2.2 View Certificate Request	134
13.3 Trusted CA	136
13.4 Import Trusted CA Certificate	137
13.5 View Trusted CA Certificate	137
13.6 Certificates Technical Reference	138
13.6.1 Verify a Certificate	139
Log	141
14.1 Log Overview	141
14.1.1 What You Can Do in this Chapter	141
14.1.2 What You Need To Know	141
14.2 System Log	142
14.3 Security Log	142
Traffic Status	144
15.1 Traffic Status Overview	144
15.1.1 What You Can Do in this Chapter	144
15.2 WAN Status	144
15.3 LAN Status	145
ARP Table	147
16.1 ARP Table Overview	147
16.1.1 How ARP Works	147
16.2 ARP Table	148
Routing Table	149
17.1 Routing Table Overview	149
17.2 Routing Table	149
Cellular WAN Status	152
18.1 Cellular WAN Status Overview	152
18.2 Cellular WAN Status	152
System	157
19.1 System Overview	157
19.2 System	157
User Account	158
20.1 User Account Overview	158
20.2 User Account	158
20.2.1 User Account Add/Edit	159
Remote Management	161
21.1 Overview	161
21.2 MGMT Services	161
21.3 MGMT Services for IP Passthrough	162
21.4 Trust Domain	163
21.5 Add Trust Domain	164
21.6 Trust Domain for IP Passthrough	164
21.7 Add Trust Domain	165
Time Settings	166
22.1 Time Settings Overview	166
22.2 Time	166
E-mail Notification	169
23.1 E-mail Notification Overview	169
23.2 E-mail Notification	169
23.2.1 E-mail Notification Edit	170
Log Setting	172
24.1 Log Setting Overview	172
24.2 Log Setting	172
Firmware Upgrade	175
25.1 Overview	175
25.2 Firmware Upgrade	175
Backup/Restore	177
26.1 Backup/Restore Overview	177
26.2 Backup/Restore	177
26.3 Reboot	178
Diagnostic	180
27.1 Diagnostic Overview	180
27.2 Ping/TraceRoute/Nslookup Test	180
Troubleshooting	182
28.1 Overview	182
28.2 Power and Hardware Connections	182
28.3 Zyxel Device Access and Login	182
28.4 Internet Access	184
28.5 UPnP	185
28.6 SIM Card	186
28.7 Cellular Signal	186
Appendices	188
Customer Support	189
IPv6	195
Legal Information	202

Match case Limit results 1 per page

Chapter 18 Cellular WAN Status

LTE Series User’s Guide

154

IP Passthrough

Enable

This displays if IP Passthrough is enabled on the Zyxel Device.

IP Passthrough allows a LAN computer on the local network of the Zyxel Device to have access

to web services using the public IP address. When IP Passthrough is configured, all traffic is

forwarded to the LAN computer and will not go through NAT.

IP Passthrough

Mode

This displays the IP Passthrough mode.

This displays

Dynamic

and the Zyxel Device will allow traffic to be forwarded to the first LAN

computer requesting an IP address from the Zyxel Device.

This displays

Fixed

and the Zyxel Device will allow traffic to be forwarded to a specific LAN

computer on the local network of the Zyxel Device.

Cellular Status

This displays the status of the cellular Internet connection.

Data Roaming

This displays if data roaming is enabled on the Zyxel Device.

4G roaming is to use your Zyxel Device in an area which is not covered by your service provider.

Enable roaming to ensure that your Zyxel Device is kept connected to the Internet when you are

traveling outside the geographical coverage area of the network to which you are registered.

Operator

This displays the name of the service provider.

PLMN

This displays the PLMN number.

Access

Technology

This displays the type of the mobile network (such as LTE, UMTS, GSM) to which the Zyxel Device is

connecting.

Band

This displays the current LTE band of your Zyxel Device (WCDMA2100).

RSSI

This displays the strength of the WiFi signal between an associated wireless station and an AP.

The normal range is -30dBm to -79dBm. If the value drops below -80dBm, try moving the

associated wireless station closer to the Zyxel Device to get better signal strength.

Cell ID

This shows the cell ID, which is a unique number used to identify the Base Transceiver Station to

which the Zyxel Device is connecting.

The value depends on the Current Access Technology:

•

For GPRS, it is the Cell Identity as specified in 3GPP-TS.25.331.

•

For UMTS, it is the Cell Identity as defined in SIB3 3GPP-TS.25.331, 3GPP-TS.24.008.

•

For LTE, it is the 28-bit binary number Cell Identity as specified in SIB1 in 3GPP-TS.36.331.

The value is ‘0’ (zero) or ‘N/A’ if there is no network connection.

Physical Cell ID

This shows the Physical Cell ID (PCI), which are queries and replies between the Zyxel Device and

the mobile network it is connecting to. The normal range is 1 to 504.

UL Bandwidth

(MHz)

This shows the LTE channel bandwidth from device to base station. According to 3GPP

specifications, the bandwidths defined by the standard are 1.4, 3, 5, 10, 15, and 20 MHz. The

wider the bandwidth the higher the throughput.

DL Bandwidth

(MHz)

This shows the LTE channel bandwidth from base station to LTE device. According to 3GPP

specifications, the bandwidths defined by the standard are 1.4, 3, 5, 10, 15, and 20 MHz. The

wider the bandwidth the higher the throughput.

RFCN

This displays the Radio Frequency Channel Number of DL carrier frequency used by the mobile

network to which the Zyxel Device is connecting.

The value depends on the Current Access Technology:

•

For GPRS, it is the ARFCN (Absolute Radio-Frequency Channel Number) as specified in 3GPP-

TS.45.005.

•

For UMTS, it is the UARFCN (UTRA Absolute Radio-Frequency Channel Number) as specified in

3GPP-TS.25.101.

•

For LTE, it is the EARFCN (E-UTRA Absolute Radio-Frequency Channel Number) as specified in

3GPP-TS.36.101.

The value is ‘0’ (zero) or ‘N/A’ if there is no network connection.

Table 63

System Monitor > Cellular WAN Status (continued)

LABEL

DESCRIPTION