Alesis PerformancePad Pro User Manual - Page 31

Pattern, Empty, Adding A New Drum To A Step, Erase A Drum Sound From A Step, Change A Drum Sound's

Get Alesis PerformancePad Pro PDF manuals and user guides View all Alesis PerformancePad Pro manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

First, you will need to make sure that you are in Pattern Mode (PATTERN should be displayed in the upper right corner of the screen). To enter Pattern Step Edit Mode, press the STEP EDIT button. BEAT SUB-BEAT PAD NUMBER The display now shows the beat and sub-beat. If a drum event exists on this beat/sub-beat, the display will also show the drum pad that played the event and the event volume. If more than one drum event occurs on the same sub-beat, the PAGE UP/DOWN buttons step forward or backward respectively through each drum one at a time. If no drum event exists on this beat/sub-beat, the display will show no pad number, and EMPTY in place of volume data. EVENT VOLUME To navigate through the steps at the current quantization rate, use the PAGE UP button to move forward or PAGE DOWN to move backward. If a drum exists between those beats that fall on the current quantization value, the drum will sound as you go past it, but the display will not stop on that drum. If swing is on, step mode will step in "swinged" increments. ADDING A NEW DRUM TO A STEP While in Pattern Step Edit Mode, use the PAGE buttons to select the step where the drum is to be added. Press the pad that corresponds to the sound you want to add. That drum, along with its volume (how hard the pad was hit), will be recorded into the displayed step. If you play a pad and there is already a drum event played by that pad on the displayed step, you will edit the volume rather than add another event. This is true even if there are several events on the displayed beat, and an event other than the one to be edited is showing. ERASE A DRUM SOUND FROM A STEP While in Pattern Step Edit Mode, use the PAGE buttons to locate the step containing the drum to be erased. While holding down the ERASE button, press REC (ENTER). The drum that was being displayed will be erased. CHANGE A DRUM SOUND'S VOLUME IN A GIVEN STEP Use the PAGE buttons to select the step containing the drum whose volume needs to be changed. Either press a number button from 1-8 (1=softest, 8=loudest), use the INC / DEC buttons or VALUE dial, or tap the displayed drum pad at the desired level. If you play a pad to change the level and there are several events on the same step, the display need not show the specific drum whose volume you want to edit. EXIT STEP EDIT MODE To exit step mode, press STOP, RECORD SETUP, or PLAY (the latter will begin playing the Pattern from the beginning). 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
31
First, you will need to make sure that you are in Pattern Mode (
PATTERN
should be displayed in
the upper right corner of the screen).
To enter Pattern Step Edit Mode, press the STEP EDIT
button.
The display now shows the beat and sub-beat. If
a drum event exists on this beat/sub-beat, the
display will also show the drum pad that played
the event and the event volume. If more than
one drum event occurs on the same sub-beat,
the PAGE UP/DOWN buttons step forward or
backward respectively through each drum one
at a time.
If no drum event exists on this beat/sub-beat,
the display will show no pad number, and
EMPTY
in place of volume data.
To navigate through the steps at the current quantization rate, use the PAGE UP button to move
forward or PAGE DOWN to move backward. If a drum exists between those beats that fall on the
current quantization value, the drum will sound as you go past it, but the display will not stop on
that drum. If swing is on, step mode will step in "swinged" increments.
ADDING A NEW DRUM TO A STEP
While in Pattern Step Edit Mode, use the PAGE buttons to select the step where the drum is to be
added. Press the pad that corresponds to the sound you want to add. That drum, along with its
volume (how hard the pad was hit), will be recorded into the displayed step.
If you play a pad and there is already a drum event played by that pad on the displayed step, you
will edit the volume rather than add another event. This is true even if there are several events on
the displayed beat, and an event other than the one to be edited is showing.
ERASE A DRUM SOUND FROM A STEP
While in Pattern Step Edit Mode, use the PAGE buttons to locate the step containing the drum to
be erased. While holding down the ERASE button, press REC (ENTER). The drum that was
being displayed will be erased.
CHANGE A DRUM SOUND'S VOLUME IN A GIVEN STEP
Use the PAGE buttons to select the step containing the drum whose volume needs to be
changed. Either press a number button from 1-8 (1=softest, 8=loudest), use the INC / DEC
buttons or VALUE dial, or tap the displayed drum pad at the desired level. If you play a pad to
change the level and there are several events on the same step, the display need not show the
specific drum whose volume you want to edit.
EXIT STEP EDIT MODE
To exit step mode, press STOP, RECORD SETUP, or PLAY (the latter will begin playing the
Pattern from the beginning).
BEAT
SUB-BEAT
PAD NUMBER
EVENT VOLUME