Asus TS300-E4 PX4 User Guide - Page 62
Chassis footpads and roller wheels
 |
View all Asus TS300-E4 PX4 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 62 highlights
2.10.6 Chassis footpads and roller wheels The barebone server system is shipped with four footpads attached to the bottom of the chassis for stability. You need to remove these footpads if: • if you want to replace the footpads with the bundled roller wheels • you wish to install the system to a rack (Refer to "Chapter 3 Installation options" of this user guide, and to the "Rackmount Kit" user guide for instructions) To remove the footpads: 1. Lay the system chassis on its side. 2. Use a flat screwdriver to flip out the top layer of a footpad. 3. Remove the footpad by rotating it counterclockwise. 4. Repeat steps 2 and 3 to remove the other three footpads. 2-40 Chapter 2: Hardware setup
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57 -
58 -
59 -
60 -
61 -
62 -
63 -
64 -
65 -
66 -
67 -
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
 |
 |
Chapter 2:
Hardware setup
2-40
2.10.6
Chassis footpads and roller wheels
The barebone server system is shipped with four footpads attached to the bottom
of the chassis for stability. You need to remove these footpads if:
•
if you want to replace the footpads with the bundled roller wheels
•
you wish to install the system to a rack
(Refer to “Chapter 3
Installation options” of this user guide, and to the
“Rackmount Kit” user guide for instructions)
To remove the footpads:
1.
Lay the system chassis on its side.
2.
Use a flat screwdriver to flip out the
top layer of a footpad.
4.
Repeat steps 2 and 3 to remove the other three footpads.
3.
Remove the footpad by rotating it
counterclockwise.