Bowflex Ultimate 2 Assembly Manual - Page 31

STEP 19, Cable Adjustment

Get Bowflex Ultimate 2 PDF manuals and user guides View all Bowflex Ultimate 2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

30 Assembling Your Bowflex Ultimate® 2 STEP 19 Parts: Left Shoulder Bar • Squat Frame (Box 2) • Shoulder Bars (Box 2) Tool: 5/16" Nylock Nut • Hex Key (3/16") and (5/32") • Wrench (1/2") & (7/16") - or Adjustable Wrench Right Shoulder Bar (has handle and cable) Button Head Screw (1/4" x 3/4") Front 19-1 Position Shoulder Bars against back of Squat Frame with bend in arms pointing 1/4" Nylock Nut towards the front of the frame. 19-2 Install and completely tighten the side screws, washers and nylock nuts. 19-2 Remove the hardware securing the Lock Pin Assembly to the Squat Frame. Washer Lock Pin Assembly Squat Frame Side Screw Button Head (5/16" x 1 3/4") 19-3 Align holes in Lock Pin Assembly and Squat Frame. 19-4 Re-install and completely tighten Lock Pin Assembly hardware. Hardware (1:1): 4 Pan Head Allen Bolt (5/16" X 1 3/4") 8 Washers (5/16") 4 Nylock Nut (5/16") Cable Adjustment The Release Cable should be adjusted so that there is enough tension to keep the cable from laying on the metal frame. In Lock most cases this adjustment will be fine out Nut of the box. If the cable needs adjustment, loosen the locknut and turn the Adjusting Barrel counter-clockwise until cable is taut. The release cable may stretch with use. Check the cable tension regularly and adjust if needed. Release Cable Adjusting Barrel Metal Frame

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
30
Assembling Your Bowflex Ultimate
®
2
STEP 19
Parts:
• Squat Frame (Box 2)
• Shoulder Bars (Box 2)
Tool:
• Hex Key (3/16”) and (5/32”)
• Wrench (1/2”) & (7/16”)
- or Adjustable Wrench
19-1
Position Shoulder Bars against back of
Squat Frame with bend in arms pointing
towards the front of the frame.
19-2
Install and completely tighten the side screws,
washers and nylock nuts.
19-2
Remove the hardware securing the Lock Pin
Assembly to the Squat Frame.
19-3
Align holes in Lock Pin Assembly and
Squat Frame.
19-4
Re-install and completely tighten Lock Pin
Assembly hardware.
Hardware
(1:1)
:
Left Shoulder Bar
Front
Right Shoulder Bar
(has handle and cable)
Side Screw
Button Head (5/16” x 1 3/4”)
Squat Frame
Lock Pin Assembly
1/4” Nylock Nut
Washer
Button Head Screw
(1/4” x 3/4”)
5/16” Nylock Nut
4 Pan Head Allen Bolt (5/16” X 1 3/4”)
8 Washers (5/16”)
Cable Adjustment
The Release Cable should be adjusted so
that there is enough tension to keep the
cable from laying on the metal frame. In
most cases this adjustment will be fine out
of the box. If the cable needs adjustment,
loosen the locknut and turn the Adjusting
Barrel counter-clockwise until cable is taut.
The release cable may stretch with use.
Check the cable tension regularly and
adjust if needed.
Metal Frame
Release Cable
Adjusting Barrel
Lock
Nut
4 Nylock Nut
(5/16”)