Brother International DCP-7040 Users Manual - English - Page 68

Start, Copy operation in progress, Stop/Exit, Error Message, Cause, Action, Fuser Error - drum end soon

Get Brother International DCP-7040 - B/W Laser - All-in-One PDF manuals and user guides
UPC - 012502620655
View all Brother International DCP-7040 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Error Message Fuser Error Init Unable XX Jam Rear Jam Inside Jam Tray No Paper Out of Memory Print Unable XX Scan Unable XX Toner Life End Toner Low Cause Action The temperature of fuser unit Turn the power switch off, wait a few does not rise at a specified seconds, and then turn it on again. Leave the temperature within specified time. machine for 15 minutes with the power on. The fuser unit is too hot. The machine has a mechanical Disconnect the machine from the power for problem. several minutes and then reconnect it. The paper is jammed in the back (See Paper jams on page 58.) of the machine. The paper is jammed inside the (See Paper jams on page 58.) machine. The paper is jammed in the paper (See Paper jams on page 58.) tray of the machine. The machine is out of paper or paper is not properly loaded in the paper tray. Do one of the following: „ Refill the paper in the paper tray, and then press Start. „ Remove the paper and load it again, and then press Start. The machine's memory is full. Copy operation in progress Do one of the following: „ Press Start to copy the scanned pages. „ Press Stop/Exit and wait until the other operations in progress finish, and then try again. „ Clear the data from the memory. (See Out of memory message on page 29.) Print operation in process Reduce print resolution. (See Advanced tab in the Software User's Guide on the CD-ROM.) The machine has a mechanical Disconnect the machine from the power for problem. several minutes and then reconnect it. The machine has a mechanical Disconnect the machine from the power for problem. several minutes and then reconnect it. The drum unit and toner cartridge assembly may have been installed improperly, or the toner cartridge is used up and printing is not possible. Do one of the following: „ Re-install the toner cartridge and drum unit assembly. „ Replace the empty toner cartridge with a new one. (See Replacing a toner cartridge on page 70.) If the LCD shows Toner Low, you can still print; however, the machine is telling you that the toner cartridge is near the end of its life and the toner will soon run out. Order a new toner cartridge now. 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
56
Fuser Error
The temperature of fuser unit
does not rise at a specified
temperature within specified time.
Turn the power switch off, wait a few
seconds, and then turn it on again. Leave the
machine for 15 minutes with the power on.
The fuser unit is too hot.
Init Unable XX
The machine has a mechanical
problem.
Disconnect the machine from the power for
several minutes and then reconnect it.
Jam Rear
The paper is jammed in the back
of the machine.
(See
Paper jams
on page 58.)
Jam Inside
The paper is jammed inside the
machine.
(See
Paper jams
on page 58.)
Jam Tray
The paper is jammed in the paper
tray of the machine.
(See
Paper jams
on page 58.)
No Paper
The machine is out of paper or
paper is not properly loaded in the
paper tray.
Do one of the following:
±
Refill the paper in the paper tray, and
then press
Start
.
±
Remove the paper and load it again, and
then press
Start
.
Out of Memory
The machine’s memory is full.
Copy operation in progress
Do one of the following:
±
Press
Start
to copy the scanned pages.
±
Press
Stop/Exit
and wait until the other
operations in progress finish, and then try again.
±
Clear the data from the memory. (See
Out of memory message
on page 29.)
Print operation in process
Reduce print resolution. (See
Advanced tab
in the Software User’s Guide on the
CD-ROM
.)
Print Unable XX
The machine has a mechanical
problem.
Disconnect the machine from the power for
several minutes and then reconnect it.
Scan Unable XX
The machine has a mechanical
problem.
Disconnect the machine from the power for
several minutes and then reconnect it.
Toner Life End
The drum unit and toner cartridge
assembly may have been
installed improperly, or the toner
cartridge is used up and printing
is not possible.
Do one of the following:
±
Re-install the toner cartridge and drum
unit assembly.
±
Replace the empty toner cartridge with a
new one. (See
Replacing a toner
cartridge
on page 70.)
Toner Low
If the LCD shows
Toner Low
,
you can still print; however, the
machine is telling you that the
toner cartridge is near the end of
its life and the toner will soon run
out.
Order a new toner cartridge now.
Error Message
Cause
Action