Brother International HE-800A Instruction Manual - English - Page 72

Sewing

Get Brother International HE-800A PDF manuals and user guides View all Brother International HE-800A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

8. SEWING ８. SEWING CAUTION Turn off the power switch at the following times, otherwise the machine may operate if the treadle is depressed by mistake, which could result in injury. ▪ When threading the needle ▪ When replacing the bobbin and needle ▪ When not using the machine and when leaving the machine unattended Do not touch any of the moving parts or press any objects against the machine while sewing, as this may result in personal injury or damage to the machine. When holding the material, place your right hand at the back and your left hand at the front. If your left hand is toward the back, it may get caught in the feed arm when it operates or it might touch the moving parts of the needle trimmer and injury may result. Do not touch the motor cover during operation and for one hour after operation has finished, otherwise burns may result. Note: ▪ The feed arm can move, so be careful of the clearance. ▪ When using the machine, check that the oil is visible through the oil cap. If it cannot be seen, stop the machine and eliminate the cause of the problem. ８-１. Sewing 2153Q 3961Q 1. Turn on the power. 2. Depress the treadle to the 2nd step [C]. (Refer to "5- 2. Home position detection (preparation)".) 3. Press the SELECT key (1) to change the mode to automatic mode. 4. Press the program No. keys (2) and (3) to select the number for the program to be sewn. 5. Press the ENTER key (4). 6. Set the material in place, and then depress the treadle from [A] to the 1st step [B]. The work clamp will be lowered. 7. Depress the treadle from the 1st step [B] to the 2nd step [C]. The sewing machine will start sewing. * Once the sewing operation has completed normally, the production counter will increase by 1 if in production counter display mode (DIP switch A - No. 4 = OFF). If in lower thread counter mode (DIP switch A - No. 4 = ON), the lower thread counter will decrease by 1. * When the number of articles set by the bobbin thread counter have all been sewn, an alarm will start sounding continuously. The sewing machine will not operate during this time, even if the treadle is depressed. Press the ENTER key (4) to cancel the alarm. (Refer to "5-11. Bobbin thread counter".) 3962Q HE-800A 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
HE-800A
8. SEWING
64
８
. SEWING
CAUTION
Turn off the power switch at the following times, otherwise the machine may operate if the treadle is
depressed by mistake, which could result in injury.
▪
When threading the needle
▪
When replacing the bobbin and needle
▪
When not using the machine and when leaving the machine unattended
Do not touch any of the moving parts or press any objects against the machine while sewing, as this may
result in personal injury or damage to the machine.
When holding the material, place your right hand at the back and your left hand at the front.
If your left hand is toward the back, it may get caught in the feed arm when it operates or it might touch
the moving parts of the needle trimmer and injury may result.
Do not touch the motor cover during operation and for one hour after operation has finished, otherwise
burns may result.
Note:
▪
The feed arm can move, so be careful of the
clearance.
▪
When using the machine, check that the oil is visible
through the oil cap. If it cannot be seen, stop the
machine and eliminate the cause of the problem.
８
-
１
. Sewing
1. Turn on the power.
2. Depress the treadle to the 2nd step [C]. (Refer to “5-
2. Home position detection (preparation)”.)
3. Press the SELECT key (1) to change the mode to
automatic mode.
4. Press the program No. keys (2) and (3) to select the
number for the program to be sewn.
5. Press the ENTER key (4).
6. Set the material in place, and then depress the
treadle from [A] to the 1st step [B]. The work clamp
will be lowered.
7. Depress the treadle from the 1st step [B] to the 2nd
step [C]. The sewing machine will start sewing.
* Once the sewing operation has completed normally,
the production counter will increase by 1 if in
production counter display mode (DIP switch A - No.
4 = OFF). If in lower thread counter mode (DIP
switch A – No. 4 = ON), the lower thread counter will
decrease by 1.
* When the number of articles set by the bobbin thread
counter have all been sewn, an alarm will start
sounding continuously. The sewing machine will not
operate during this time, even if the treadle is
depressed.
Press the ENTER key (4) to cancel the
alarm. (Refer to “5-11. Bobbin thread counter”.)
2153Q
3961Q
3962Q